R INSTALLATION MANUAL Bolden Single Handle Commercial Kitchen Faucet TM KPF-1610 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone. · Flush angle stops to release any debris prior to installation.
Diagram and Parts List G B A H F C1 D E1 4 C2 C3 E2 I A. Spray Head B. Faucet Body C. Mounting Hardware C1. Rubber & Metal Washer C2. Mounting Nut C3. Mounting Screws D. Supply Hose E. Hot & Cold Waterlines E1. Hot E2. Cold F. Hose G. Weight H. Hex Wrench I.
Faucet Dimension 10 3/4" 18" (456mm) (274mm) 3 1/2" (88mm) 25° Ø1 7/8" 8 3/4" (162mm) 90° (56mm) 6 3/8" (221mm) 2 1/4" 4 1/2" (116mm) (48mm) Ø2 1/8" (578mm) 22 3/4" 17" (432mm) (54mm) 3/8" Compression Installer Tip: Shut off main water supply before installing new faucet.
Step 1. Remove mounting hardware Remove mounting hardware (C1, C2 & C3) from faucet body (B). B C1 C2 C3 Step 2. Install the faucet and mounting hardware Insert faucet body through the hole in the sink or countertop. Install the rubber washer and metal washer (C1), mounting nut (C2) and mounting screws (C3) onto the threaded mounting shank. C1 C2 C3 Step 3. Secure mounting hardware Thread the nut (C2) onto the mounting shank. Lock the nut (C2) into position by tightening the screws (C3).
Step 4. Connect the quick connector Connect the quick connector (I) to the supply hose (D) by twisting clockwise. Push the spray hose (F) firmly upward into quick connector. Pull down moderately to ensure the connection has been made. D I F Step 5. Attach the weight Install the weight (G) on the indicated mark on the spray hose (F).
Step 6. Making the waterline connections 1 Thread the nut (1) on the supply line onto the outlet of the water supply valve and tighten with a wrench. Do not overtighten. Step 7. Flushing and checking for leaks Pull the hose assembly out of the spout and remove the spray head by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water.
Replacement Parts Replacement Parts List Finish/Color Part # CH,SS,MB,SFS** KP12202 KP12003 KP12205 GRCH, GRSS, KP12204 GRSFS, BLSFS BLSS, BLMB* CH,SS,MB,SFS** KP12189 5. Spring Assembly 6. Sprayer Support Assembly CH,SS,SFS,MB, KP12206 SFSCH, SFSMB SSCH, SSMB** 1. 2. 3. 4.
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose or cartridge needs to be reseated Loosen the set screw located at the base of the handle with a hex wrench. Remove the handle and unscrew cartridge holder by hand. Tighten locking nut with an adjustable wrench.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI 61-9 UP C R C ASME A112.18.1 1.8GPM 6.8L/min maximum C R FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
