INSTALLATION MANUAL Bolden™ Single Handle Pull Down Kitchen Faucet KPF-1610 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2023 Kraus USA Plumbing LLC I Rev.
Congratulations on the purchase of your new Kraus plumbing fixture! R Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
STOP Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. R · Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List A. Spray Head B. Faucet Body C. Mounting Hardware C1. Rubber & Metal Washer C2. Mounting Nut C3. Mounting Screws D. Quick Connector E. Weight E1. Weight Clip E2. Weight F. 2.
Faucet Dimensions 10 3/4" (456mm) (274mm) 18" 3 1/2" (88mm) Ø1 7/8" 25° 8 3/4" (162mm) 6 3/8" (221mm) 90° (56mm) 2 1/4" (116mm) 4 1/2" (48mm) Ø2 1/8" (578mm) 22 3/4" 17" (432mm) (54mm) 3/8" compression Installer Tip: Shut off main water supply before installing new faucet.
Step 1. Remove mounting hardware Shut off the water supply. Remove the old faucet. Clean the mounting surface. Remove mounting hardware (C) from faucet body (B). C Step 2. Installing the faucet assembly Optional No Escutcheon Installation. Insert faucet body through the hole in the sink or countertop.
Step 3. Securing the faucet assembly Install the rubber washer and metal washer (C1) onto the threaded mounting shank. Thread the nut (C2) onto the mounting shank. Lock the nut (C2) into position by tightening the screws (C3). Do not overtighten. C1 C2 C3 Step 4. Securing the faucet assembly Push the quick connector (D) firmly upward and attach it to the receiving block (1). Pull down moderately to ensure the connection has been made.
Step 5. Installing the counterweight Install the weight clip (E1) at the point of the hose marking "weight here". Insert the weight (E2) onto the clip (E1) by sliding it down onto the clip (E1). Weight here E2 E2 E1 Weight here E1 Step 6. Making the waterline connections 1 Thread the nut (1) on the supply line onto the outlet of the water supply valve and tighten with a wrench. Do not overtighten. NOTE: Please make sure filter washers are installed before connecting to the main valve.
Step 7. Flushing and checking for leaks Pull the hose assembly out of the spout and remove the spray head by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush the water lines for one minute. This flushes away any debris that could cause damage to internal parts. Check for leaks. Retighten any connections if necessary, but do not overtighten.
Replacement Parts Replacement Parts List 1. Sprayer 6 4 2. Screen Washer 3. Sprayer Hose 5 4. Flow Regulator Assembly (1.8GPM) 7 7.1 5. Quick Connector Assembly 6. Spring Assembly 7.2 8 9 10 3 2 16 1 19 17 20 18 24 12 13 14 15 6. Spring Assembly 7. Sprayer Holder Assembly 7.1. Inverter 23 9. Index 10. Cartridge Kerox K-35 11. Bonnet Nut *Denotes spray hose assembly color options: Spray hose assembly color options: Black hose w/Brushed 12.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Bonnet nut (11) has come loose Remove the cover button (15). Loosen set screw (14) with hex wrench (22). Remove the handle. Unscrew cap (12). Tighten bonnet nut (11) with an adjustable wrench.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI/CAN 61: Q ≤ 1 UP C R C LEAD FREE IA P C MO R& R NSF/ANSI 61 T TM ASME A112.18.1 1.8GPM 6.8L/min maximum Faucet - Lifetime Limited Warranty Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is non-transferable.
How to Make a Warranty Claim If you are a consumer purchaser, please contact a Kraus Customer Service Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com R If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
