WT-5721 433 MHz Radio Controlled Projection Alarm Instruction Manual PROJECTION 02'(
TABLE OF CONTENTS Topic Inventory of Contents/ Additional Equipment About WWVB Quick Set-Up Guide Page 3 3 4 Detailed Set-Up Guide Battery Installation Program Mode Programming Sequence Function Buttons Time Zone Setting DST (Daylight Saving Time) Setting Adjustable Snooze Time Setting Date Setting 12/24-Hour Setting 6 6 6 7 7 7 7 8 Features & Operations Features Radio-Controlled Time Projection EL Backlight Indoor Temperature Remote Temperature Time Alarm Changing Display Mode (viewing seconds) Mountin
INVENTORY OF CONTENTS 1) WT-5721 Alarm Clock 2) TX6U Remote temperature sensor 3) AC adapter/transformer 4) Instruction manual and warranty card. ADDITIONAL EQUIPMENT (not included) 1) Two fresh 1.5V AA batteries (optional for alarm clock) 2) Two fresh 1.5V AA batteries (for remote sensor) FEATURES OF PROJECTION ALARM Operation of these features is in section III. 1. 2. 3. 4. 5. 6. 7. 8.
QUICK SET-UP GUIDE Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. 2. 3. 4. Have the indoor station and outdoor remote 3 to 5 apart. Batteries should be out of both units for 10 minutes. Place the batteries into the outdoor remote first then into the indoor station. (All outdoor remotes must be started before the indoor station) DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.
DETAILED SET-UP GUIDE II. BATTERY INSTALLATION A. B. REMOTE TEMPERATURE SENSOR 1. Remove the battery cover. Observing the correct polarity, install 2 AA batteries. The batteries will fit tightly (to avoid start-up problems make sure that they do not spring free during installation). 2. Replace the battery cover. Battery Cover PROJECTION ALARM 1. Remove the battery cover. 2. Observe the correct polarity, and install 2 AA batteries. 3.
III. PROGRAM MODE To enter the Program Mode hold down the “SET” button for 1 second, until the time zone (“-5” default) flashes in the lower left. The Program Mode Guide is laid out in a manner that allows you to program each function separately, or you can follow the instructions entirely to program the projection alarm. Complete programming is usually done for the initial set-up, and will require you to skip step 1 of programming sections III through VIII.
D. DST (DAYLIGHT SAVING TIME) SETTING Note: The DST default is “On”, meaning that the WWVB will automatically change the time according to Daylight Saving Time in the spring and fall. For areas that do not recognize DST changes (Arizona and parts of Indiana) turn the DST “OFF”. 1. 2. 3. E. Hold down the “SET” button for 1 second (the selected time zone will flash); press and release the “SET” button once more until “On” flashes in the lower left and “DST” flashes in the upper right.
9. H. Press and release the “SET” button to confirm the calendar settings, and to advance to select either 12 or 24-hour time display. 12/24-HOUR SETTING Note: Setting to the 24 hour mode (also known as Military Time) will also change the temperature to display in °C instead of °F. 1. 2. 3. Hold down the “SET” button for 1 second (the selected time zone will flash), press and release the “SET” button 9 more times, until the “12” hour time display flashes in the time LCD.
IV. FEATURES & OPERATIONS A. FEATURES 1. 2. 3. 4. 5. 6. 7. 8. Radio-controlled time and date Projection of time and/or remote temperature EL backlight Six modes of date/seconds/temperature display Indoor temperature Remote outdoor temperature Dual alarms Adjustable snooze B. RADIO-CONTROLLED TIME AND DATE 1. The projection alarm will automatically search for the time signal upon initial set-up and every night. 2.
6. 7. The projector case can be rotated 180° to further help orient the projected display. The intensity of the projection can be adjusted to three different settings as well as turned “off” by pressing the light Intensity button. When turned off, the projection will 02'( Light intensity Display Mode Display Direction only come on when a button is pressed. The intensity cannot be set for the projected display when set to “off”.
G. TIME ALARM The projection alarm has two separate alarms for time, “ALM1” and “ALM2”. The alarms have a different sound; ALM1 increases in volume after 25 seconds, and again after 50 seconds. ALM2 is a constant volume. The total duration is 96 seconds for each alarm. 1. SETTING THE ALARM a. Press and hold “ALM1” OR “ALM2” for two seconds until the alarm time is flashing. b. Press and release “ALM1/HOUR” to advance the hour, and “ALM2/MIN” to advance the minute.
V. MOUNTING THE REMOTE TEMPERATURE SENSOR A. The Remote Temperature Sensor can be mounted in two ways: 1) with the use of screws, or 2) using the adhesive tape. B. MOUNTING WITH SCREWS 1. 2. 3. 4. 5. C. MOUNTING WITH ADHESIVE TAPE 1. 2. VI. Remove the mounting bracket from the Remote Temperature Sensor. The bracket should snap off easily. Place the mounting bracket over the desired location. Through the three screw holes of the bracket, mark the mounting surface with a pencil.
TROUBLESHOOTING Problem: Solution: Problem: Solution: Problem: Solution: Problem: Solution: Problem: Solution: Problem: Solution: Problem: Solution: The Projection is faint 1) Change intensity setting 2) Use AC adapter 3) Darken surroundings 4) Use fresh batteries (if AC is not used) The LCD is faint. 1) Replace the batteries. “OFL” appears in the indoor temperature LCD. 1) Move unit to an area with warmer or cooler surrounding temperature. Current surrounding temperatures are outside measuring range.
SPECIFICATIONS FOR WT-5721 Temperature: Measuring range: Checking intervals: Power source: AC Adapter (included) Battery type: Battery life: Dimensions (L x W x H): 32°F to 122°F with 0.2°F resolution (indoor) -21.8°F to 140°F with 0.2°F resolution (outdoor) (0°C to 50°C with 0.1°C resolution) Every 10 seconds indoor, 3 times in 10 minutes for remote temperature. Input: 120VAC/60Hz Output: DC 6V/100MA Station: 2 x AA, 1.5V (Alkaline) (optional) Sensor: 2 x AA, 1.
WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures.
For warranty work, technical support, or information contact: La Crosse Technology 2809 Losey Blvd. S. La Crosse, WI 54601 Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacrossetechnology.com FCC ID: OMO-01RX (receiver) OMO-01TX (sensor) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1.
