Owner Manual

ASSEMBLY AND INSTALLATION
1. Take the parts out of the mounting package . Screw the end of the NIPPLE (4) into the center hole of the
MOUNTING BRACKET (2) and thread both 1/8” IPS HEX NUT(5) several turns onto each end of the
NIPPLE(4) but do not tighten the 1/8” IPS HEX NUTS (5). Pull the SUPPLY WIRES (9 & 11) and the
SUPPLY GROUND WIRE (8) out from the OUTLET BOX (1) and attach the MOUNTING
BRACKET (2) assembly to the OUTLET BOX (1) using the slotted holes of the MOUNTING
BRACKET (2) and the MOUNTING SCREWS (3) provided. (See Fig. 1)
2. Thread the SCREW COLLAR LOOP (6) onto the bottom end of the NIPPLE (4). Place the CANOPY
(15) over the OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (6) and NIPPLE (4) until the
midpoint of the outside threads on the SCREW COLLAR LOOP (6) is centered (aligned) with the
surface of the CANOPY (15). Remove the CANOPY (15) and tighten both 1/8” IPS HEX NUTS (5)
down on the MOUNTING BRACKET (2) and the SCREW COLLAR LOOP (6). (See Fig. 1)
3. Thread FIXTURE LOOP (19) to CENTER NIPPLE (20).
4. Attach two CLOSABLE LINKS (18) to each end of the CHAIN (17), and then attach one CLOSABLE
LINK (18) onto the FIXTURE LOOP (19). Slide the THREADED RING (16) and the CANOPY (15)
onto the CHAIN (17) (in that order) and attach the other CLOSABLE LINK (18) to the SCREW
COLLAR LOOP (6). (See Fig. 1 and 2)
5. Unravel the fixture lead wires (10 and 12) and FIXTURE GROUND WIRE (7) and thread them
through every other link of the CHAIN (17) starting with the chain link attached to the FIXTURE
LOOP (19). Feed the fixture lead wires (10 and 12) and FIXTURE GROUND WIRE (7) through the
SCREW COLLAR LOOP (6) and NIPPLE (4) assembly. Pull the fixture lead wire (10 and 12) and the
FIXTURE GROUND WIRE (7) upward to remove any excess slack. (See Fig. 1)
6. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (9) to
the SMOOTH FIXTURE LEAD WIRE (10) and the WHITE SUPPLY WIRE (11) to the RIBBED
FIXTURE LEAD WIRE (12). Loop the FIXTURE GROUND WIRE (7) around the GROUND
SCREW (14) of the MOUNTING BRACKET (2). (Note: Be sure to provide an extra 3” length of the
GROUND WIRE (7).) Connect the remaining FIXTURE GROUND WIRE (7) to the SUPPLY
GROUND WIRE (8) using a WIRE CONNECTOR (13). Place wiring and connections inside the
OUTLET BOX (1). (See Fig. 1)
ASSEMBLY AND INSTALLATION (Continued)
7. Slide the CANOPY (15) and the THREADED RING (16) up the CHAIN (17). Place the CANOPY (15) over the
OUTLET BOX (1) and secure it in place by screwing the THREADED RING (16) onto the SCREW COLLAR LOOP
(6). (See Fig.1)
8. Place the GLASS SHADES (23) over the SOCKETS (22), then secure with SPACERS (24) and SOCKET RINGS (25).
(See Fig. 2)
9. Screw light bulbs into the sockets and make sure they do not exceed the maximum wattage
specified on the fixture’s wattage rating label, MAXIMUM 60W.
INSTALLATION IS NOW COMPLETED
ASSEMBLY & INSTALLATION
INSTRUCTIONS
Please read carefully and save these instructions, as you may need them at a later date.
GENERAL
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If
you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are missing by
referencing the illustrations on the installation instructions.
CAUTION
Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
1. OUTLET BOX
2. MOUNTING BRACKET
3. MOUNTING SCREW
4. NIPPLE
5. 1/8” IPS HEX NUT
6. SCREW COLLAR LOOP
7. FIXTURE GROUND WIRE
8. SUPPLY GROUND WIRE
9. BLACK SUPPLY WIRE
10. SMOOTH FIXTURE LEAD WIRE
11. WHITE SUPPLY WIRE
12. RIBBED FIXTURE LEAD WIRE
13. WIRE CONNECTOR
14. GROUND SCREW
15. CANOPY
16. THREADED RING
17. CHAIN
18. CLOSABLE LINK
19. FIXTURE LOOP
20. CENTER NIPPLE
21. FIXTURE BODY
22. SOCKET
23. GLASS SHADE
24. SPACER
25. SOCKET RING