Owner Manual

ManualsBrandsLark Manor ManualsCottage & Country SconcesBurnley 1-Light Wallchiere

ASSEMBLY & INSTALLATION

INSTRUCTIONS

Please read carefully and save these instructions, as you may need them at a later

date.

CAUTION

Turn off the main power at the circuit breaker before installing the fixture, in order to

prevent possible shock.

GENERAL

All electrical connections must be in accordance with local and National Electrical

Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring

connections obtain the services of a qualified electrician.

Remove the fixture and the mounting package from the box and make sure that no

parts are missing by referencing the illustrations on the installation instructions.

ASSEMBLY AND INSTALLATION

1. At the center of the BACK PLATE (2) there are eight perforated slots. Knock out

the set matches your OUTLET BOX (1).

2. Screw the #8-32 FIXTURE MOUNTING SCREWS (13) into the BACK PLATE

(2) and thread the #8-32 HEX NUTS (14) onto the FIXTURE MOUNTING

SCREWS (13), as shown. Secure the position of the FIXTURE MOUNTING

SCREWS (13) by tightening the HEX NUTS (14) against the BACK PLATE (2).

3. Carefully pass the power supply (6&8) wires and the SUPPLY GROUND WIRE

(5) through the center hole of the BACK PLATE (2). Secure the BACK PLATE

(2) to the OUTLET BOX (1) with MOUNTING SCREWS (3).

4. Attach the BLACK SUPPLY WIRE (8) to the SMOOTH (or BLACK) FIXTURE

LEAD WIRE (9) by using the WIRE CONNECTOR (10). At the same manner,

attach the WHITE SUPPLY WIRE (6) to the RIBBED (or WHITE) FIXTURE

LEAD WIRE (7). Loop the FIXTURE GROUND WIRE (4) around the

GROUND SCREW (11) of the BACK PLATE (2). (Note: Be sure to provide an

extra 3” length of the FIXTURE GROUND WIRE (4) for connection to the

SUPPLY GROUND WIRE (5).) Tighten the GROUND SCREW (11). Connect

the remaining FIXTURE GROUND WIRE (4) to the SUPPLY GROUND WIRE

(5) using a WIRE CONNECTOR (10). Place wiring and connections inside the

OUTLET BOX (1).

5. Place the COVER PLATE (12) onto the FIXTURE MOUNTING SCREWS (13),

and secure it into place using the BALL FINIALS (15) provided.

ASSEMBLY AND INSTALLATION (Continued)

6. Place the GLASS SHADE (17) over the SOCKET (16), then secure with the SPACER

(18) and SOCKET RING (19).

7. Screw light bulb into the socket and make sure it does not exceed the maximum wattage

specified on the fixture’s wattage rating label, MAXIMUM 100W.

INSTALLATION IS NOW COMPLETED

1. OUTLET BOX

2. BACK PLATE

3. MOUNTING SCREW

4. FIXTURE GROUND WIRE

5. SUPPLY GROUND WIRE

6. WHITE SUPPLY WIRE

7. RIBBED (OR WHITE) FIXTURE LEAD WIRE

8. BLACK SUPPLY WIRE

9. SMOOTH(OR BLACK) FIXTURE LEAD WIRE

10. WIRE CONNECTOR

11. GROUND SCREW

12. COVER PLATE

13. #8-32 FIXTURE MOUNTING SCREW

14. #8-32 HEX NUT

15. BALL FINIAL

16. SOCKET

17. GLASS SHADE

18. SPACER

19. SOCKET RING

Summary of content (2 pages)

PAGE 1
ASSEMBLY AND INSTALLATION (Continued) 6. Place the GLASS SHADE (17) over the SOCKET (16), then secure with the SPACER (18) and SOCKET RING (19). ASSEMBLY & INSTALLATION INSTRUCTIONS Please read carefully and save these instructions, as you may need them at a later date. 7. Screw light bulb into the socket and make sure it does not exceed the maximum wattage specified on the fixture’s wattage rating label, MAXIMUM 100W.
PAGE 2
Limited Warranty We warrants all its Products to be free from defects in material and workmanship, subject to certain conditions and exclusions, for period of one year from the date the Product was shipped to the original end use purchaser. We will warranty its product only if it is sold through an authorized dealer.