User manual

03
LED LENSER® * SEO 5
push a second time within 2 seconds, the SEO5
glows with lower brightness (Light Function
Dim). When you push the second time within
2 seconds but keep the button pressed down,
you can change the brightness infinitely. For
the time that the switch button is pressed, the
brightness varies between full and reduced
brightness. The SEO 5 extinguishes (blinks)
for a short moment as soon as the highest or
lowest brightness is reached. At both ends of
the SEO 5 goes off shortly, and then again to
be lighter or darker(a blinking signal happened
at both ends). When you release the switch
button you lock the current brightness. This
brightness is retained for the Light Function
Dim even if you turn the head lamp off.
After the Light Function Dim (altogether 3
times fast switching, i.e. you do not wait longer
than 2 seconds between each switching) comes
the Light Function Signal (slow even flashing)
in the Light Program White.
Additional switching turns SEO 5 off and the
circle starts again with the Light Function
Power when you press the switch button again.
So the Light Functions are in a loop. But please
note that you turn off the head lamp by every
switching if since the previous switching more
than 2 seconds have elapsed. For example in
case you let pass more than 2 seconds after
you turned the Light Function Dim on the next
switching will not change to head lamp to Light
Function Signal but will turn the SEO 5 off.
5.2 Light Program „Red Night Vision“
If the Lighting Program „Red Night Vision“ is
enabled (see Point 5), you can use the red light of
the head lamp.
When the switch button is pressed, when the SEO
5 is off, the head lamp glows in the Light Function
Power at full brightness in red. When you switch
a second time within 2 seconds, the SEO 5 blinks
in the Light Function Signal (slow even flashing).
The Light Function Signal is the last Light
Function that can be used in the Light Program
“Red Night Vision” so additional switching turns
SEO 5 off and the circle starts again with the
Light Function Power when you press the switch
button again.
So the Light Functions are in a loop. But please
note that you turn off the head lamp by every
switching if since the previous switching more
than 2 seconds have elapsed. For example in
case you let pass more than 2 seconds after
you turned the Light Function Power on the next
switching will not change to head lamp to Light
Function Signal but will turn the SEO 5 off.
6 „Transport Lock“
Under Point 5 it has been described how to
switch between the white and the red LED. This
takes place when the SEO 5 is off and the switch
button is pressed only for approx. 2 seconds. The
head lamp will change from red to white or from
white to red. But when the switch is pressed
longer (approx. 5 seconds) until the light turns off
you have enabled the „Transport Lock“. Then the
SEO 5 can not be turned on again but the red LED
flashes for a short moment to indicate that this
function is activated in case the switch button is
pressed. The SEO 5 therefore cannot be switched
on, either intentionally or unintentionally and
inadvertently consume energy.
Only when you hold the switch button pressed for
5 seconds again this function („Transport Lock“)
is deactivated again and the lamp is in the Light
Program White.
7. Reset function
If the used alkaline batteries, NiMH-
Accumulators or an Accumulator-Pack of a
SEO 7R are taken out the battery box you have
"reset" the SEO 5.
You have thus reset a few functions:
- The „Transport Lock“ (see Point 6) is
deactivated
- The Light Function Dim (see Point 5.1) is set
to low brightness
- The Light Program White (see Point 5) is
activated
8. Use of rechargeable batteries
The SEO 5 indicates by the flashing of the red
LED that it is running out of energy in near
future. Please change the batteries respectively
the accumulators in time.
In the scope of delivery of the SEO 5 are alkaline
batteries. These can not be charged!
The following information applies only in case
you use in your SEO 5 NiMH-Accumulators
respectively the Accumulator-pack of a SEO
7R. These are not scope of delivery of SEO 5!
In case NiMH-Accumulators (see Point 1) are
used, these must be charged in approved
external chargers.
Always charge in a dry place!
Do you use the Accumulator-Pack of a SEO 7R
please note that this can only be charged with
the charger and the charger cable of the SEO
7R or by a USB port (see below)!
In case the plug and the charger are not
connected already please connect them so that
the connection clicks.
The charger of SEO 7R has a USB port, which
must be connected with the corresponding
port at the charging cable in order to charge
the SEO 7R Accumulator-pack. The other
side of the charging cable (micro USB) must
be connected to the Accumulator-pack. You
will therefore have to open the battery box
possibly. The Accumulator-pack of SEO 7R
has two charging ways, either it loaded in the
battery box of SEO 5 or can be removed out of
the battery box for charging. The charger of the
SEO 7R can only be used for charging of this
Accumulator-pack.
The last step is to connect the plug into a
socket (Input: 100 V to 240 V / 50 Hz to 60 Hz).
When charging is completed (after maximum 2
to 3 hours), unplug the charger from the socket
again and the charging cable (micro-USB) of
the Accumulator-pack. But it is no problem to
go on loading the Accumulator-pack although it
is already full.
Instead of connecting the charging cable of the
SEO 7R to the USB port of the charger, you can
also connect it to a different USB port (5 V /
900 mA) e.g. of a computer.
While using our optionally available car USB
charger connection (Led Lenser Car Charger:
Item no. 0380), the Accumulator-pack also can