Use and Care Manual

CLEANING AND MAINTENANCE
USING FOOT PEDAL
6
7
LEM Products • West Chester, OH 45011 • PH: 877-536-7763 • lemproducts.com
LEM Products • West Chester, OH 45011 • PH: 877-536-7763 • lemproducts.com
1. Plug the foot pedal into the Stuffer Motor (As shown below). Turn speed all the way up.
2. Plug motor into grounded outlet and press the power button to turn the motor on. The light will illuminate.
3. Pressing the foot pedal can only control the Piston moving down. When the Piston moves down to the bottom of the
cylinder, the Piston will stop automatically and begin to raise. Release the pressure on the foot pedal.
Note: If the down button has been manually pressed the foot pedal will not work. Press the stop button. Now the
foot pedal will control the down motion of the piston.
Note: Pressing the foot switch for 3 seconds or more will engage the auto up function when the pedal is released.
Always unplug the foot switch and turn off the motor when stuffing is complete or walking away.
Prior to rst use hand wash all removable parts in hot soapy water. The motor cannot be immersed. Wipe
down the motor and the frame with a damp cloth. The gear box on the stuer is not water resistant. Do
not use spray on the upper half of the stuer frame. Doing so may cause damage to the internal parts of
the stuer which may void your warranty.
DISASSEMBLY:
• Remove the Retaining Ring and Stung Tube from the Cylinder.
· To help in removing excess meat from the Stung Tube tightly twist a corner of a paper towel, insert the twisted end into
the Stung Tube and push meat out. A small wooden dowel or other straight, dull object is also helpful for this task (LEM
sells a cleaning brush (SKU: 1360) specically for this purpose. See www.LEMProducts.com for more details.)
• Raise the Piston until it is in the upmost position and free of the Cylinder.
• Slide the cylinder out of the frame and remove any leftover meat from the bottom of the cylinder. Fry up a sausage
burger to enjoy during clean up! Remove any leftover meat from the bottom of the Cylinder and fry up a sausage burger
to enjoy during clean up!
• Unscrew the Piston from the Main Shaft.
• With your ngers or another dull object, like the tip of a spoon, carefully remove the Piston Gasket from the Piston.
• Remove the Air Release from the piston.
• Wash all parts in hot soapy water and hand dry.
Note: The motor cannot be submerged. Wipe it down with a damp cloth.
• With a clean, damp cloth wipe down the stuer stand and gear box. Do not spray gear box.
ASSEMBLY:
• Replace the Piston Gasket on the Piston. Lightly grease the Gasket with vegetable oil, mineral oil or silicone spray.
• Reassemble the Air Release Valve.
• Return assembled Piston to the Main Shaft. Turn until hand tight.
• Place the cylinder on the frame by lining up the tabs with the locating clips on the frame base.
MAINTENANCE:
The Stuer Motor is constructed of heavy-duty corrosion resistant materials for a lifetime of dependable use. Be sure to
follow all of the “IMPORTANT SAFEGUARDS” in the booklet to ensure safety and function of the Stuer.
1. ALWAYS unplug the Stuer Motor from the power source before cleaning!
2. DO NOT Immerse any part of this Stuer Motor in water or any other liquid!
3. DO NOT place the Stuer Motor in the dishwasher.
4. Clean the outside Stuer Motor with a damp cloth and dry thoroughly.
5. The Stuer Motor is permanently lubricated. DO NOT take the Stuer Motor apart for any reason.
6. Always unplug foot switch and turn motor o when stung is complete.
WARNING
Severe injury risk!
At all times keep fingers clear of the top of the cylinder.
CAUTION
The sensor plug of the stuer motor must be plugged into the socket entirely.
Otherwise, the piston will not be able to automatically stop at the cylinder bottom or
at the highest position. This may cause motor overload damaging the motor the
stuer or both.
SENSOR PLUG
The sensor plug is on the motor and MUST BE plugged into the stuer prior to the motor being installed. The sensor
plug enables the piston of the stuer to automatically stop when the piston reaches the bottom of the cylinder or has
reached the top of the cylinder. This plug must be installed for this function to properly work. If the sensor is not
plugged in damage may occur to the stuer, cylinder and motor. This type of damage is not covered under warranty. It
is the users responsibility to ensure the sensor is plugged in prior to use. Always turn the motor o and remove the foot
switch from the motor when stung is complete or walking away from the stuer. Do not leave the stuer unsupervised
around children. Sever injury could occur.