SR-600 BT USER MANUAL www.lenco.com PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
IMPORTANT INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1.
17. Do not attempt to dismantle, open or repair this product yourself. If a fault occurs, seek advice from your local qualified service technician or contact the distributor via the telephone number at the back of this instruction manual. 18. Caution marking and nameplate are located on bottom of product. WARNING DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD This product contains a coin/button cell battery.
PREPARATION FOR USE ACCESSORIES Unpack the unit carefully to remove all the accessories from the packing. Verify that the following accessories are present before setting up the unit. Accessories> Main Unit X1 AC adaptor X1 User Manual X1 Button cell X 2 (LR44/AG-13) (For Clock backup) Energy Saving (Auto Power System-APS) Unit will automatic turn to 'Standby' mode after 20 minutes while unit at power on mode but not play and speaker no output. This is APS for save energy efficiency.
. 6. SKIP FORWARD/TUNING PLAY/PAUSE button button 7. VOLUME - button 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21.
Backup Batteries Batteries are preloaded in the unit. Remove the insulation tab from the battery compartment to activate the battery back-up before first use. To replace the batteries, carefully open the battery door of the BATTERY BACK-UP COMPARTMENT (#21). Remove the old batteries and follow the polarity marking to insert 2 x new LR44/AG13 button cells into the compartment and close the battery door. BATTERY WARNING 1. Be sure that the batteries are installed correctly. Wrong polarity may damage the unit.
NOTE: The clock settings may be lost if the main power switch is turned off and the battery drains after a period of time. If this occurs, you will need to reset the clock. LISTENING TO THE RADIO 1. 2. Press and hold the button (#10) to turn on the unit. Tap the button (#10) to select Radio mode, the radio frequency will show on LED Display (#12). 3. Press and hold the button (#4) or button (#5) to search for the next / previous available station.
Note : In Radio Mode, press and hold the Button (#6). The SR-600 BT will scan the whole band start from the lowest frequency and store all the available radio stations start from lowest preset channel number. Those previous stored radio stations may be overwritten. RECALLING PRESET MEMORY CHANNELS To recall a preset station, 1. In radio mode, tap the PRESET/TIME SET button (#2), the preset number will appear on display. 2.
2. If your Bluetooth enabled device does not support A2DP profile, it will not play the music through the speaker, even if paired (linked). 3. Remember to turn off the SR-600 BT when you have finished listening, slide the MAIN POWER ON/OFF SWITCH (#15) to OFF position. 4. Don't forget to switch off the power of your external audio device as well. USING SR-600 BT AS A HANDS-FREE SPEAKERPHONE To use your Bluetooth speaker as a speakerphone for receiving a phone call from a Bluetooth enabled phone. 1.
This feature is phone dependent and may not operate on all cell phones or devices. PRESET EQ The SR-600 BT features 5 different EQ modes to enhance your listening experience.
3. 4. cable into the device you wish to charge. Observe the battery charge indicator on your device to make sure the charging process starts normally. Unplug the cable when your device is fully charged. CAUTION: Before charging, please refer to the user manual of the device you wish to charge to make sure the charging current requested does not exceed 1A (1000mA). Overloading the charging circuit may damage the SR-600 BT permanently and void the warranty. 1.
CLEANING THE UNIT To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning. If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any wax or polish sprays on the cabinet. If the front panel becomes dirty or smudged with fingerprints it may be cleaned with a soft cloth slightly dampened with a mild soap and water solution. Never use abrasive cloths or polishes as these will damage the finish of your unit.
Sound is distorted. Unit gets warm after extended play at high volume. Volume level is set too high. Decrease the volume. Sound source is distorted. If the cell-phone original sound source is of poor quality, distortion and noise are easily noticed with high-power speakers. Try a different audio source such as a music CD. If you are using an external sound source like older generation of iPod, try reducing the output volume on the device itself. Also try turning bass boost OFF or change the EQ setting.
This product operates at 2400 - 2483.5 MHz and is designated only to be used inside a normal household environment. This product is suited for this purpose within all EU counties. Hereby, STL Group BV, Ankerkade 20 NL 5928 PL Venlo, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at https://lencosupport.zendesk.
Lenco offers service and warranty in accordance to European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer. Important note: It is not possible to send products that need repairs to Lenco directly. Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires. This device is not suitable for professional use.
