Instructions / Assembly

ManualsBrandsLeviton ManualsBreaker Boxes150 Amp 30-Space Outdoor Load Center Main Breaker

PK-A3230-10-00-0A

For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only)

1 800 405-5320 (Canada Only) www.leviton.com

PK-A3230-10-00-0A

IMPORTANT SAFETY INSTRUCTIONS - READ ALL INSTRUCTIONS BEFORE USING.

INSTALLATION INSTRUCTIONS

Nos. LPxxx-3B, LPxxx-3L

Outdoor Load Center Enclosure

PATENTS PENDING

LIMITED PRODUCT WARRANTY

For Leviton’s limited product warranty, go to www.leviton.com. For a printed copy of the warranty you may call 1-800-323-8920.

WARNING

INSTALLATION

WARNING: TO AVOID FIRE, SHOCK OR DEATH: TURN OFF

POWER SUPPLYING THIS EQUIPMENT, AND CONFIRM

POWER IS OFF, before installing, removing or servicing

this equipment.

Step 1: Remove Load Center Door (Optional)

NOTE: The load center door can be removed for easier installation.

a. Lift door (A) upward to remove from hinge (B) (ﬁg. 1).

b. When installation is complete, align the door hinge with the

hinge pin and insert downward until door is seated.

Step 2: Bottom feed applications (Optional)

NOTE: The

Leviton

Load Center interior should be inverted for

bottom feed applications.

NOTE:

Install the closing plate (included) to the overhead opening of

the enclosure for bottom feed applications.

NOTE: Before removing any knockouts from the enclosure, consult

the local electrical code to determine the knockout requirements.

a. Remove the mounting screws (C) and the green ground

bonding screw (D)

b. Invert the interior (E) and place into slots (F).

c. Replace the mounting screws (C) and green ground bonding

screw (D) to secure the interior

(ﬁg. 2)

. Torque all mounting

screws to 20 +/- 2 in-lbs.

d. To remove knockouts (G), ﬁrst strike the center of the

knockout.

e. Pry each ring (H) up, one at a time, and grip both ends with a

pair of pliers.

f. Use the pliers to bend the rings (H) until they disconnect from

the enclosure (ﬁg. 3).

Step 3: Enclosure Mounting

Surface or Semi-Flush Mounting

Remove deadfront (W) by loosening the securing screw (X) and

lifting the deadfront (W) off the enclsoure.

b. Remove

mounting knockouts (I) from the back of the enclosure

(ﬁg. 4).

c. Use outdoor approved screws or nails (not provided) in the

mounting

knockouts

(I) to secure the enclosure to the wall.

Fig. 1

Fig. 3

Fig. 2

Fig. 4

• TO AVOID FIRE, SHOCK OR DEATH: TURN OFF POWER SUPPLYING THIS EQUIPMENT, AND CONFIRM POWER IS OFF,

before installing, removing or servicing this equipment.

• This equipment MUST BE installed and serviced by an electrician.

• Replace all doors and covers before connecting power to this equipment.

• To be installed and/or used in accordance with electrical codes and regulations.

Green ground

bonding screw

(D)

Mounting screws

(x7)(C)

Interior (E)

inverted

Slot

(F)

Mounting

Knockouts

(I)

Knockout

(G)

Ring

(H)

Ring

(H)

Door

(A)

Hinge

(B)

Hinge pin

WEB VERSION

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Outdoor Load Center Enclosure PK-A3230-10-00-0A Nos. LPxxx-3B, LPxxx-3L IMPORTANT SAFETY INSTRUCTIONS - READ ALL INSTRUCTIONS BEFORE USING. WARNING • TO AVOID FIRE, SHOCK OR DEATH: TURN OFF POWER SUPPLYING THIS EQUIPMENT, AND CONFIRM POWER IS OFF, before installing, removing or servicing this equipment. • This equipment MUST BE installed and serviced by an electrician. • Replace all doors and covers before connecting power to this equipment.
PAGE 2
Step 4: Phase, Neutral and Ground Conductors WARNING: Use ONLY approved ﬁttings and clamps to avoid damage to wires. a. Bring the phase (J), neutral (K) and ground (L) conductors into the enclosure through the overhead conduit opening or a bottom-feed knockout. b. Determine whether or not the application requires the use of a main circuit breaker (M) (ﬁg. 5), or if main lugs (N) (ﬁg. 6) can be used based on the local electrical codes. c.