Installation Guide

C. OPB15 Power Base Installation:
In addition to the regular mounting methods shown, the OSWxx can be mounted to the
OPB15 Power Base.
1. Install the OPB15 per the installation sheet included with the OPB15.
2. Remove the OSWxx from the box and pass the low-voltage wires through the
neck/base cover assembly.
3. Screw the neck plastic nut to the sensor body to hold assembly together while
connecting the wire leads.
4. Remove the two-part
connector from the
OPB15 noting the
orientation it was in
before removal.
5. Connect the wires
from the sensor to the
appropriate locations
on the terminal block.
6. Push the terminal block
on to the OPB15 pins.
7. Align the raised arrow
on the side of the base
cover with the arrow on
the mounting ring of the
OPB15 and push on
and twist to install.
8. Rotate the assembly
and adjust the neck for
either ceiling or wall
configuration aiming
per the diagram.
9. Tighten the plastic nut
on the neck to lock the
position of the sensor.
Infrared Wall Mounted Occupancy Sensor
Cat. Nos. OSWHB-I, OSWLR-I, OSWWV-I
To be used with 24VDC OSPxx Series, OPB15, miniZ and CN100 Power Pack Class II Low-Voltage Wiring
INSTALLATION INSTRUCTIONS
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF
POWER at circuit breaker or fuse and test that power is off before wiring!
Step 1
INSTALLING YOUR OCCUPANCY SENSOR
NOTE: Use check boxes when Steps are completed.
√
WARNINGS AND CAUTIONS:
• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.
• Ifyouareunsureaboutanypartoftheseinstructions,consultaqualiedelectrician.
• Sensorsmustbemountedonavibrationfreesurface.
• Allsensorsmustbemountedatleast6feetawayfromairvents.
• Donottouchthesurfaceofthelens.Cleanoutersurfacewithadampclothonly.
Mounting Option Diagram A
Occupancy Sensor Mounted to Wallboard Using Screws
4. Install the mounting base of the wall sensor to the wallboard or ceiling using the
included screws, nuts and washers.
5. Pass wires through the base cover/neck assembly (refer to Mounting Option
Diagram A).
6. Class II Wiring: Connect low-Voltage wires from Power Pack to Sensor per
WIRING DIAGRAM as follows: Twist strands of each lead tightly and, with circuit
conductors, push firmly into appropriate wire connector. Screw connectors on
clockwise making sure that no bare conductor shows below the wire connectors.
Secure each connector with electrical tape.
7. Push wire connections through the center hole of the back cover and into the wall
or ceiling.
8. Snap neck and base cover onto mounting base in the desired orientation. Align
arrows on mounting base and base cover, push on and turn to lock base cover to
mounting base.
9. Push wires through the hole and begin to fasten the plastic nut around the back
of the sensor body. Move the sensor body to the desired orientation and then
continue to tighten the nut around the sensor body. NOTE: The neck is a two
position assembly with catches to hold it in position for either ceiling or wall
mounting.
10. Restore power at circuit breaker or fuse to Power Pack. INSTALLATION IS
COMPLETE.
Mounting Option Diagram B
Occupancy Sensor Mounted to Octagon
Box Installed Flush to Wallboard
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
This device must not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Occupancy Sensor Mounted to Octagon
Box Installed Flush to Wallboard Ceiling or Drop Ceiling
B. Wall or Ceiling Using Junction Box or Surface Mount Raceway
Installation (refer to Mounting Diagrams):
NOTE: You may use the mounting screws, nuts and washers included, or screws in
combination with commercially available wall anchors.
NOTE: Listed below are suggested JUNCTION BOX installation applications which
requiremountingtoconduitinoneofthefollowingways.
Low-Voltage
Wires
Wallboard Base Cover/
Neck Assembly
Sensor
Plastic Nut
Mounting Screws
(2 places)
Low-Voltage
Wires
Drop Ceiling
Sensor
Base Cover
Screw, Nut and
Washer
(2 places)
Plastic Nut
Mounting Base
Mounting
Screws
(2 places)
Mounting Base
Occupancy Sensor Mounted to Wallboard or
Drop Ceiling Using Screws, Nuts and Washers
Wallboard
Mounting Screws (2 places)
Mounting Base
Base Cover
Sensor
Octagon Box
4" x 1 1/2" deep
4" Octagon
Raised Cover
4" Octagon
Raised Cover
Sensor
Mounting Base
Base Cover
Octagon Box
4" x 1 1/2" deep
Wallboard Ceiling
Wire Mold
Back Cover
Wire Mold Raceway
Wallboard
Base Cover
Mounting Base
Sensor
Mounting Screws for Wire Mold Fixture (2 places)
Wire Mold Round Fixture
Box Cat. No. 5738
(for raceway mount)
Occupancy Sensor Mounted to Wallboard
Using Round Fixture with Raceway
CATALOG ITEMS
Catalog No.
OSWHB-I0W
OSWLR-I0W
OSWWV-I0W
Description
High Bay
Long Range
Wide View
Coverage
55 ft. mounted at 30 ft
100 ft. mounted at 10 ft.
2500sq.ft.
Current
Consumption
20mA
20mA
20mA
Tools needed to install your Sensor
Slotted/Phillips Screwdriver Electrical Tape
Pliers Pencil
Cutters
Sensor (1)
#8-32 x 1/2" Screw (2)
#8-32 x 1-1/2" Screw (2)
#8-32 Washer and Nut (2)
Parts included list
DESCRIPTION
The Occupancy Sensor is a low-voltage infrared sensor that works with the OSPxx
Series, OPB15, miniZ and CN100 power pack to automatically control lighting. The
sensor turns the lights on and keeps them on whenever occupancy is detected and will
turn them off after the ‘delayed-off time’ has expired.
The sensor continually analyzes and adjusts to changing conditions. The sensor uses
the latest microprocessor-based technology which permits it to continually adjust and
optimize its performance.
Infrared motion detection gives higher false triggering immunity that yields a sensor
with excellent performance.
Listed are 3 typical installation options (A, B and C). Choose one that best suits your
needs. Other methods of installation may be possible but they have not been described
here. Note that the wall sensor can be wall mounted or ceiling mounted simply by
rotating the neck. This gives greater flexibility in attaining the desired coverage.
A. Wall or Ceiling Installation Using Screws (Mounting Option A):
NOTE: You may use the mounting screws, nuts and washers included, or screws
in combination with commercially available wall anchors.
1. Select location for mounting of sensor for your application (refer to Mounting
Location Diagram).
2. Make a hole in the wallboard or ceiling large enough to pass the wire
connections and wire nuts through (approximately 1" diameter).
3. Drill holes for mounting screws using mounting base as template.
Typical Installations:
Step 3
Strip Gage (measure
bare wire here)
Preparing and connecting wires:
Step 2
1/2"
(1.3 cm)
Step 3 cont'd Step 3 cont'd Step 3 cont'd
4" Octagon 2.125" Deep
Electrical Box
8-32 Screws
(2 places)
Sensor
Power Base
Base Cover
Tw o-Part
Terminal
Connector
Sensor
PK-93596-10-00-2C