RJP-201B/202B Remote Jack Pack Installation & Setup Guide Warranty © Copyright 2008, LG Electronics U.S.A., Inc.
For Customer Support/Service, please call: 1-888-865-3026 www.lgcommercial.com The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Table of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5 Installation Installation in Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installer Connections . . . .
Overview The Remote Jack Pack (RJP) contains circuitry to determine the presence of a signal at each input jack. (Note: Audio In, Audio In L-R and Video In inputs detect the presence of the inserted plug, regardless if a signal is present or not.) When a source is detected, its priority is compared to the priority of other sources which may be present. If the newly-connected active source is of higher priority than the existing source(s), the RJP directs the TV display panel to that source.
Overview CLEANING CAUTION: Since the end-user jack panel is exposed, use extreme caution when cleaning. Do not use liquid cleaners on the connections panel. Do not allow liquids to be spilled, sprayed onto or otherwise come into contact with the connections panel on both the end-user side and the installer side. Clean with a slightly damp cloth.
Installation in Wall Cutout The RJP can only be installed in a vertical position into the cutout provided in the wall. Vertical mounting in the cutout is required so that a liquid will not be able to flow into the RJP. The cable wiring assembly and individual cables will need to be connected to the RJP. Route cable bundle to avoid damage from chaffing, binding etc. The RJP must only be installed in the cutout opening. It will then need to be secured with the two retainer clips and machine screws provided.
Installer Connections The RJP cables listed below are to be connected to the TV display panel. CAUTION: Be sure power is turned off before attempting to connect the RJP to the TV display panel. EO L ITA DIG RGB EO OL NTR OTE REM IN O T OU AUDI T OU IO L AUD R VID VID T OU T OU T OU CO Control Cable (8-Pin RJ-45) w/Yellow Protective Sleeve Connect to RJP port on TV display panel. Audio/Video Cables Connect to Left-Right Audio/composite Video input jacks on TV display panel.
Installer Connections Contd. After completing connections between the RJP and the TV display panel, be sure the installer menu items have been updated to enable the RJP. Installer Menu item 040 Auto Camport needs to be set to 000 and 093 RJP Available needs to be set to 001. (See TV installation guide for complete instructions on new TV installations.) A brief description of each of the available RJP connections is provided below.
End-User Connections Overview The end-user simply plugs a device such as a laptop computer with the appropriate cables, as shown in the example, into the RJP connection panel. The Remote Jack Pack senses the new source connection and switches the TV to the newly-connected source. The device’s sound and image are then presented on the in-room TV display panel. The TV display panel adjusts automatically to the computer output format.
End-User Multi-Media Interface Connections 3.5 mm Stereo Audio Input Jack Connection for MP-3 player or PC audio. DIGITAL VIDEO IN PC VIDEO IN VIDEO IN AUDIO IN L Digital Video Input Port Connection for digital video sources. (portable DVD) AUDIO IN R Audio/Video Input Jacks Connection for Left-Right Audio/composite Video sources. PC Video (RGB) Input port Connection for PC Video.
End-User Connectable External Source Devices Examples of devices a guest/end-user can connect are shown to the right.
End-User Audio/Video Input Priorities End-User Audio/Video Input Priorities Note: The highest priority is listed first. Audio Inputs/Sources 1st. 2nd. 3rd. 4th. 3.5 mm Stereo Audio Jack Left - Right Audio Jacks Digital Video Audio TV Display Panel Tuner Audio (Audio Default) Video Inputs 1st. 2nd. 3rd. 4th.
Reference Cable Bundle Assembly Connect to Outputs on RJP RJP-202B Size AUDIO VIDEO L- R CONTROL RGB DIGITAL VIDEO RJP-201B Size Note: Connector set with right angle connectors is for connecting to RJP. 6. Cable Tie Mesh Sleeving Cable Assembly Approx. 3.0 Feet in Length Cable Assembly approx. 12.0 Feet in Length Output Cable Assembly Parts List Item Description No. 1. Left/Right Audio Cable. 2. Composite Video Cable. 3. RJ-45 Control Cable w/Yellow Protective Sleeves 4. RGB Cable. 5.
Accessory Cable: DVI to HDMI Adapter Cable Strain Relief Special Connections Note: DVI to HDMI Adapter Cable Male Connector Female Connector For TVs equipped with HDMI, this adapter cable will be required to connect the RJP for digital video/audio. RS-232C ..... .... ..... ..... ..... PC IN AUDIO IN UPDATE VIDEO 1 IN RS-232C CONTROL DIGTAL AUDIO OUT (OPTICAL) NORMAL (DTV) AUDIO IN M.P.I.
Specifications Application Makes available to the hotel’s guests, a multi-media interface to the in-room TV display panel. Audio/Video input jacks are provided for guest devices such as DVD/CD Players, Laptop Computers, Camcorders, etc. Installer Connections Digital Video Out RGB OUT Control Out Video Out Audio Out L-R Digital Video Connector 15-pin RGB PC Monitor Connector Control Jack (8-Pin RJ-45) 1 Vpp into 75 ohms, Composite or Y+C Combined Video Jack +/- 1 db @ 4.
Specifications Contd. Dimensions Height 2.125 Inches Width 9.0 Inches Depth 3.125 Inches Weight (Approx.) .7 Pounds End-User Device Inputs Audio In Audio In L-R Video In PC Video In Digital Video In (53.975 mm) (228.6 mm) (79.375 mm) (0.317514 kgs) 3.5mm Stereo Audio Jack Left - Right Audio Jacks (Nom In: 250mV RMS @ 22K ohms) Overload In: 1.
Troubleshooting Equipment Setup Analysis Notes • Make sure all connectors and connections are tight and secure on user device, RJP and TV. • Check to assure user device, RJP and TV are all powered up and working properly and that the TV Installer menu items are set correctly. • Audio and Video can be from different sources. Default is TV tuner Audio and Video, if no other audio/video source is connected. • Audio source must be viable.
Troubleshooting Flow Charts No Audio (or not desired Audio) No Power Power Failure? Yes Restore Power RJP Is Audio connected ? No TV Is power cord connected ? No Connect Audio Cables No Connect Power Cord RJP Are other audio devices connected ? Yes Disconnect other Audio devices Turn Power On TV Is TV turned On ? No Yes Yes Disconnect other Video devices No Turn TV On TV Is TV turned On ? No Turn TV On Yes Are Installer menu items set up? Are Installer menu items set up? Connect
Quick Setup Guide Installer RJP Quick Setup Reference Guide Following are the tasks associated with installing and setting up an RJP System. 1. Make all hard wire connections to RJP and TV. 2. Install RJP in wall cutout. 3. Plug all system components into power sources. 4. Adjust TV installer menu items 040 and 093 to enable RJP capability. (See TV installation guide for complete instructions on new TV installations.
RJP-201B/202B Warranty Remote Jack Pack Welcome to the LG family! We believe that you will be pleased with your new LG product. Please read this warranty carefully, it is a “LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state within the U.S.A. LG’S RESPONSIBILITY Warranty Term Parts Warranty Service Not Covered One year parts and labor from date of purchase or delivery date.