OWNER’S MANUAL LED TV* * Disclaimer LG LED TV applies LCD screen with LED backlights. Please read this manual carefully before operating your set and retain it for future reference. LY33** LY34** LY54** www.lg.
TABLE OF CONTENTS ENG ENGLISH TABLE OF CONTENTS 3 LICENSES 20 TROUBLESHOOTING 3 OPEN SOURCE SOFTWARE NOTICE 21 SPECIFICATIONS 23 IR CODES 24 EXTERNAL CONTROL DEVICE SETUP 24 24 RS-232C Setup Type of Connector: D-Sub 9-Pin Male RS-232C Configurations Communication Parameters Command Reference List Transmission / Receiving Protocol 4 ASSEMBLING AND PREPARING 4 6 7 8 9 9 10 11 Unpacking Parts and Button Using the Joystick Button Lifting and Moving the TV Setting up the TV - Attaching the
LICENSES / OPEN SOURCE SOFTWARE NOTICE 3 Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
ASSEMBLING AND PREPARING ENG ENGLISH NOTE yy Image shown may differ from your TV. yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual. yy The available menus and options may differ from the input source or product model that you are using. yy New features may be added to this TV in the future. yy The TV can be placed in standby mode in order to reduce the power consumption.
ENGLISH ENG ENGLISH ENG ASSEMBLING AND PREPARING 5 ENGLISH ENG Remote Control, Batteries (AAA) Owner’s Manual Cable Holder (Depending on model) Power Cord (Depending on model) Stand Screws 4EA, M4 x L14 (Only 42/47LY34**, 39/42/47/55LY54**) Stand Screws 4EA, M4 x L20 (Only 32LY34**, 32LY54**) Cable Managements 2EA (Only 32/42/47LY34**, 32/39/42/47/55LY54**) Wall Mount Spacers 2EA (Only 42LY34**, 42LY54**) Stand Base (Only 32/42/47LY34**, 32/39/42/47/55LY54**) AC-DC Adaptor (Only 28LY33**) (Dep
ASSEMBLING AND PREPARING ENG ENGLISH Parts and Button A type : 32/42/47LY34**, 32/39/42/47/55LY54** B type : 28LY33** (Except for India) Screen Screen Speakers Speakers Remote control sensor Power Indicator Joystick button1 Remote control sensor Power Indicator Joystick button1 C type : 28LY33** (Only India) Screen Speakers Remote Control Sensor Power Indicator Joystick Button1 1 Joystick Button - This button is located below the TV screen.
ASSEMBLING AND PREPARING 7 You can simply operate the TV functions, pressing or moving the joystick button up, down, left or right. Basic Functions Power On When the TV is turned off, place your finger on the joystick button and press it once and release it. Power Off When the TV is turned on, place your finger on the joystick button and press it once for a few seconds and release it. (However, if the Menu button is on the screen, pressing and holding the joystick button will let you exit the Menu.
ASSEMBLING AND PREPARING ENG ENGLISH Lifting and Moving the TV When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. yy When transporting a large TV, there should be at least 2 people. yy When transporting the TV by hand, hold the TV as shown in the following illustration. CAUTION yy Avoid touching the screen at all times, as this may result in damage to the screen.
ASSEMBLING AND PREPARING ENGLISH ENG Setting up the TV Attaching the Stand * Image shown may differ from your TV. (Only 32/42/47LY34**, 32/39/42/47/55LY54**) (Only 28LY33**) 1 1 1 2 A Stand Base B Stand Base Stand Base 2 2 M4 x L14 (Only 42/47LY34**, 39/42/47/55LY54**) M4 x L20 4EA (Only 32LY34**, 32LY54**) 9 CAUTION yy When attaching the stand to the TV, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.
ASSEMBLING AND PREPARING ENG ENGLISH Mounting on a Table 1 Securing the TV to a Wall Lift and tilt the TV into its upright position on a table. -- Leave a 10 cm (minimum) space from the wall for proper ventilation. (This feature is not available for all models.) 10 cm 10 cm 2 10 cm 10 cm Connect the power cord to a wall outlet. 1 CAUTION yy Do not place the TV near or on sources of heat, as this may result in fire or other damage.
ASSEMBLING AND PREPARING CAUTION Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer. 10 cm 10 cm yy Disconnect the power first, and then move or install the TV. Otherwise electric shock may occur.
MAKING CONNECTIONS ENG ENGLISH MAKING CONNECTIONS Antenna Connection Connect the TV to a wall antenna socket with an RF cable (75 Ω). * Image shown may differ from your TV. * Any separate cable is not provided. This section on MAKING CONNECTIONS mainly uses diagrams for the LY34** models. Connect various external devices to the TV and switch input modes to select an external device. For more information on external device’s connection, refer to the manual provided with each device.
MAKING CONNECTIONS Network Setup Wired Network Connection (Only 28LY33**) (Depending on model & country) (Only LY54**) This TV can be connected to a local area network (LAN) via the LAN port. After making the physical connection, the TV needs to be set up for network communication. (Image shown may differ from your TV.
MAKING CONNECTIONS ENG ENGLISH Other Connections Connect your TV to external devices. For the best picture and audio quality, connect the external device and the TV with the HDMI cable as shown. * Image shown may differ from your TV. * Any separate cable is not provided.
OPTICAL AUDIO IN MAKING CONNECTIONS 15 ENG USB IN 2 ENGLISH ENG (Only 32/42/47LY34**, 32/39/42/47/55LY54**) H/P OUT 2 USB HUB HUB USB MHL passive cable HUB Mobile Phone Mobile Phone VOLUME Headphone CONTROL AV IN EXTERNAL SPEAKER OUT 1 IN ANTENNA/ AUDIO LNB IN ANTENNA/ CABLE Satellite CABLE IN EXTERNAL AUDIO COMPONENT RGB IN (PC)IN RGB RS-232C IN (CONTROLRS-232C & SERVICE) IN (PC) IN (CONTROL & SERVICE) STEREO (8 Ω) RS-232C IN CABLE IN 3 RED BLUE WHITE BLUE GREEN RED GREEN
MAKING CONNECTIONS ENG ENGLISH (Only 28LY33**) + - /DVI IN 1 2 AV AV (RGB) CLOCK KER OUT OPTICAL OUT DIGITAL AUDIO OUT /DVI IN IN NT/DVI) ME CONTROL 1 IN1 OPTICAL DIGITAL AUDIO OUT AVRS-232C IN 2 RGB IN (PC) AUDIO IN COMPONENT OPTICAL OPTICAL AUDIO OUT (COMPONENT/RGB/DVI) NENTIN RS-232C IN DIGITAL AUDIO OUT EXTERNAL SPEAKER OUT REO (8 Ω) SPEAKER H/P OUT OUT AUDIO IN OMPONENT/DVI) STEREO (8 Ω) LEFT GND EXTERNAL SPEAKER OUT IN1 LNB IN ANTENNA/ 1 RGB IN (PC) (CONTROL & SERVICE)
MAKING CONNECTIONS 17 CLOCK USB IN 2 HUB USB USB HUB MHL passive cable HUB H/P 2OUT (MHL) AV 1 Mobile Phone AV (RGB) H/P OUT H/P OUT /DVI IN AUDIO IN OPTICAL OPTICAL IN1 (COMPONENT/DVI) DIGITAL IN DIGITAL LAN VOLUME AUDIOAUDIO OUTCONTROL AUDIO OUT AUDIO EXTERNAL EXTERNAL SPEAKERSPEAKER OUT OUTIN RS-232C 2 IN1 RS-232C IN COMPONENTRGB IN (PC) (CONTROL & SERVICE) RS-232C IN IN RS-232C IN ANTENNA/ LNB IN ANTENNA/ CABLEIN Satellite CABLE 1(ARC) RGB IN (PC) (CONTROL & SERVICE) (CONTROL & SE
REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. or CAUTION yy Do not mix old and new batteries, as this may damage the remote control.
REMOTE CONTROL 19 ENERGY AV MODE ENGLISH ENG (Only LY54**) (POWER) Turns the TV on or off. ꕊ ENERGY SAVING Adjusts the brightness of the screen to reduce energy consumption. AV MODE Selects an AV mode. INPUT Changes the input source. TV/RAD Selects Radio, TV and DTV programme. INPUT TV/ RAD SAVING 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW Number buttons Enters numbers. LIST Accesses the saved programme list. Q.VIEW Returns to the previously viewed programme.
MAINTENANCE / TROUBLESHOOTING ENG ENGLISH MAINTENANCE Cleaning your TV Clean your TV regularly to keep the best performance and to extend the product lifespan. CAUTION yy Make sure to turn the power off and disconnect the power cord and all other cables first. yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall outlet to prevent possible damage from lightning or power surges.
SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions. For the power supply and power consumption, refer to the label attached to the product. MODELS 32LY34** 42LY34** 47LY34** 32LY340C-TA 42LY340C-TA 47LY340C-TA Dimensions (W x H x D) With stand (mm) 732 x 481 x 207 961 x 612 x 218 1073 x 676 x 247 Without stand (mm) 732 x 431 x 55.5 961 x 567 x 55.5 1073 x 629 x 55.8 Weight With stand (kg) 6.2 9.5 12.7 Without stand (kg) 6.
SPECIFICATIONS ENG ENGLISH RGB-PC, HDMI/PC Supported Mode Component Port Connecting Information Component ports on the TV Y Video output ports on DVD player PR PR Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 640 x 350 31.468 70.09 720 x 400 31.469 70.08 Y PR PR Y B-Y R-Y 640 x 480 31.469 59.94 Y Cb Cr 800 x 600 37.879 60.31 Y Pb Pr 1024 x 768 48.363 60.00 1280 x 768 47.776 59.
IR CODES yy This feature is not available for all models. Code (Hexa) Function 08 (POWER) Note Remote control Button (Power On/Off) F0 TV/RAD Remote control Button 39 SUBTITLE Remote control Button 30 AV MODE Remote control Button 79 RATIO Remote control Button 0B INPUT Remote control Button 10-19 Number Key 0-9 Remote control Button 53 LIST Remote control Button 1A Q.
EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH EXTERNAL CONTROL DEVICE SETUP RS-232C Setup RS-232C Configurations Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. VOLUME CONTROL Connect the serial port of the control device to the RS232C jack on the product back panel. IN are not supplied with OPTICAL Note: RS-232C connection cables EXTERNAL DIGITAL 1 SPEAKER OUT the product.
EXTERNAL CONTROL DEVICE SETUP 25 yy Baud rate: 9600 bps (UART) yy Data length: 8 bits yy Parity : None ENGLISH ENG Communication Parameters yy Stop bit: 1 bit yy Communication code: ASCII code yy Use a crossed (reverse) cable. Command Reference List (Depending on Model) model) 01. Power 02. Aspect Ratio 03. Screen Mute 04. Volume Mute 05. Volume Control k a DATA (Hexadecimal) 00 to 01 k c (See p. 27) k d (See p. 27) k e 00 to 01 k f 00 to 64 06. Contrast k g 00 to 64 07.
EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] [Command 2] [Set ID] : First command to control the TV.(j, k, m or x) : Second command to control the TV. : You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled.
EXTERNAL CONTROL DEVICE SETUP 27 04. Volume Mute (Command: k e) ►► To control Power On/Off of the set. ►► To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : Power On Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To show Power On/Off.
EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH 09. Tint (Command: k j) 13. Balance (Command: k t) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu. ►► To adjust balance. You can also adjust balance in the AUDIO menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 00 to Green : 64 * Refer to ‘Real data mapping’. See p.30. Ack [j][ ][Set ID][ ][OK/NG][Data][x] Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. See p.
EXTERNAL CONTROL DEVICE SETUP ►► Select channel to following physical number. ►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr] Data00 : High channel data Data01 : Low channel data ex. No. 47 -> 00 2F (2FH) No. 394 -> 01 8A (18AH), DTV No.
EXTERNAL CONTROL DEVICE SETUP 22. Input select (Command: x b) ENG ENGLISH (Main Picture Input) ►► To select input source for main picture.
Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service.