OWNER’S MANUAL M2394A M2794A Make sure to read the Safety Precautions before using the product. Keep the User's Guide(CD) in an accessible place for furture reference. See the label attached on the product and give the information to your dealer when you ask for service.
PREPARATION FRONT PANEL CONTROLS ■ This is a simplified representation of the front panel. The image shown may be somewhat different from your set.
PREPARATION BACK PANEL INFORMATION ■ This is a simplified representation of the back panel. The image shown may be somewhat different from your set. 1 2 3 4 5 6 COMPONENT IN AUDIO IN (RGB/DVI) AV IN Y VIDEO RGB IN (PC) (MONO) L VIDEO PB 1 HDMI 7 PR 2 AC IN L ANTENNA/ CABLE IN AUDIO RS-232C IN (CONTROL & SERVICE) AUDIO R DVI-D IN (PC) R S-VIDEO 8 9 1 Power Cord Socket This set operates on AC power. The voltage is indicated on the Specifications page.
PREPARATION STAND INSTALLATION ■ The image shown may be somewhat different from your set. 1 Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. 2 Insert the s t a n d b a s e into the product 3 Attach the monitor to the Stand Base by turning the screw to the right.
PREPARATION DETACHING STAND ■ The image shown may be somewhat different from your set. 1 Place the set screen side down on a cushion or soft cloth. 2 Detach the monitor to the Stand Base by turning the screw to the left. 3 Turn the screw by using the screw handle 4 Pull the stand base.
PREPARATION WALL MOUNT: HORIZONTAL INSTALLATION For proper ventilation, allow a clearance of 4 inches on each side and from the wall. Detailed installation instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. 4 inches 4 inches 4 inches 4 inches 4 inches DESKTOP PEDESTAL INSTALLATION For proper ventilation, allow a clearance of 4 inches on each side and from the wall.
PREPARATION POSITIONING YOUR DISPLAY ■ The image shown may be somewhat different from your set. Adjust the position of the panel in various ways for maximum comfort. • Tilt range -6° ~ -2° 12°~ 18° -5° ~ -2° 7°~ 13° LOCATION Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a position to allow a free flow of air.
PREPARATION KENSINGTON SECURITY SYSTEM - The product is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. - For detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System. For further information, contact h t t p : / / w w w . k e n s i n g t o n . c o m, the internet homepage of the Kensington company.
EXTERNAL EQUIPMENT SETUP ■ To prevent equipment damage, never plug in any power cords until you have finished connecting all equipment. ANTENNA CONNECTION For optimum picture quality, adjust antenna direction. ■ An antenna cable and converter are not supplied.
EXTERNAL EQUIPMENT SETUP ■ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. ■ The image shown may be somewhat different from your set. HD RECEIVER SETUP When connecting with a component cable 1 Connect the SET-TOP outputs to the C O M P O N E N T I N V I D E O sockets (Y PB PR) on the set. 2 Connect the audio cable from the SET-TOP to C O M P ON E N T I N A U D I O sockets of the set.
EXTERNAL EQUIPMENT SETUP When connecting with a HDMI Connect the HDMI output of the digital set-top box to the H D M I jack on the set. 1 1 HDMI 2 2 Press the INPUT button to select HDMI1 or HDMI2. Signal HDMI 480i/576i No 480p/576p Yes 720p/1080i Yes 1080p Yes 1 When connecting with a HDMI to DVI cable 1 Connect the digital set-top box to H D M I jack on the set. 1 HDMI 2 2 Connect the audio output of the digital set-top box to the A U D I O I N ( R G B / D V I ) jack on the set.
EXTERNAL EQUIPMENT SETUP DVD SETUP When connecting with a component cable 1 Connect the video output sockets (Y PB PR) of the DVD to the C O M P O N E N T I N V I D E O sockets (Y PB PR) of the set. 2 Connect the audio cable from the DVD to C O M P O N E N T I N A U D I O sockets of the set. 3 Press the I N P U T button to select C o m p o n e n t. 4 Press the P L A Y button on the DVD. The DVD playback picture appears on the screen.
EXTERNAL EQUIPMENT SETUP When connecting HDMI cable 1 HDMI 1 Connect the HDMI output of the DVD to the H D M I jack on the set. 2 Press the INPUT button to select HDMI1 or HDMI2. 2 1 ! NOTE G Set can receive the video and audio signal simultaneously by using a HDMI cable. G If the DVD player does not support Auto HDMI, you need to set the DVD output resolution appropriately. G HDMI support PCM audio format only.
EXTERNAL EQUIPMENT SETUP VCR SETUP To avoid picture noise (interference), leave an adequate distance between the VCR and set. ■ Typically a still picture is shown on the VCR. If a user uses 4:3 picture format for a long time, an afterimage may remain on the sides of the screen. ■ When connecting with an antenna ANTENNA IN/ CABLE IN ANT OUT S-VIDEO ANT IN OUTPUT SWITCH VIDEO L R 1 2 Wall Jack Antenna 1 Connect the RF out socket of the VCR to the aerial socket of the set.
EXTERNAL EQUIPMENT SETUP When connecting with a RCA cable R ANT OUT ANT IN Press the PLAY button on the VCR. The VCR playback picture appears on the screen. 1 L 3 S-VIDEO VIDEO Press the INPUT button to select AV. AUDIO R 2 AV IN (MONO) L Connect the audio/video out sockets of the VCR to AUDIO/VIDEO in sockets of the set. VIDEO 1 S-VIDEO ! NOTE G If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set.
EXTERNAL EQUIPMENT SETUP PC SETUP This product provides Plug and Play capability, meaning that the PC adjusts automatically to the set's settings. When connecting with a D-sub 15 pin cable 1 Connect the signal cable from the RGB output socket of the PERSONAL COMPUTER to the RGB IN(PC) of the set. 2 Connect the audio cable from the PC to the A U D I O I N ( R G B / D V I ) jack of the set. 3 Press the INPUT button to select RGB PC. 4 Switch on the PC, and the PC screen appears on the set.
EXTERNAL EQUIPMENT SETUP When connecting with a DVI cable 1 Connect the DVI output of the PC to the D V I - D I N jack on the set. DVI-D IN (PC) 2 AUDIO IN (RGB/DVI) Connect the audio cable from the PC to the A U D I O I N ( R G B / D V I ) jack of the set. 1 2 AUDIO DVI OUTPUT ! NOTE G If the set is cold, there may be a small “flicker” when the set is switched on. This is normal, there is nothing wrong with the set.
EXTERNAL EQUIPMENT SETUP BACK COVER FOR WIRE ARRANGEMENT Tie cables together with a cable tie as shown in the illustration.
EXTERNAL EQUIPMENT SETUP RGB/DVI[PC] Resolution 720x400 640x480 800x600 1024x768 1152x864 1280x1024 1680x1050 1600x1200 1920x1080 Horizontal Frequency(kHz) Vertical Frequency(Hz) 31.468 31.469 37.500 37.879 46.875 48.363 60.123 67.500 63.981 79.976 64.674 65.290 75.000 66.
WATCHING TV /PROGRAMME CONTROL REMOTE CONTROL KEY FUNCTIONS When using the remote control, aim it at the remote control sensor on the set. (Depends the country the remote control can be provided different.) A TYPE 1 1 TV/PC POWER INPUT TV/PC Selects TV or PC mode. Switches the set on. POWER Switches the set on or off. 2 3 MUTE PIP TEXT I/II 1 2 3 4 5 6 7 8 9 INPUT External input mode rotates in regular sequence. Switches the set on. 2 PIP Switches the sub picture PIP, DW mode.
WATCHING TV /PROGRAMME CONTROL (Depends the country the remote control can be provided different.) A TYPE MENU 5 7 SLEEP ARC/ 5 * MENU Selects a menu. (Refer to the p.22) SLEEP Sets the sleep timer. (Refer to the p.46) RETURN ARC/* Selects your desired picture format.(Refer to the p.30,31) 6 HOLD SIZE MIX RETURN Allows the user to move return one step in an interactive application or other user interaction function.
WATCHING TV /PROGRAMME CONTROL TURNING ON THE SET When your set is turned on, you will be able to use its features. Firstly, connect the power cord correctly. ■ To turn set on, press the , I N P U T, P R 1 PR D / E, D / E button on the set or press the P O W E R, I N P U T, N U M B E R ( 0~9 9 ) buttons on the remote control and the set will switch on.
WATCHING TV /PROGRAMME CONTROL ON SCREEN MENUS SELECTION AND ADJUSTMENT Your set's OSD (On Screen Display) may differ slightly from what is shown in this manual. 1 Press the M E N U button and then D / 2 Press the G button and then D / 3 Change the setting of an item in the sub or pull-down menu with F / You can move to a higher level menu by pressing the O K. E button to display each menu. E button to select a menu item. G button.
WATCHING TV /PROGRAMME CONTROL AUTO PROGRAMME TUNING Up to 100 TV stations can be stored by programme numbers (0 to 99). Once you have preset the stations, you will be able to use the P R D / E or NUMBER buttons to scan the stations you have programmed. Stations can be tuned using automatic or manual modes. All stations which can be received are stored by this method. It is recommended that you use Auto tuning during installation of this set. Setup 1 Press the M E N U button and then D / S e t u p menu.
WATCHING TV /PROGRAMME CONTROL MANUAL PROGRAMME TUNING Manual programme lets you manually tune and arrange the stations in whatever order you desire. Setup 1 Press the M E N U button and then D / menu. 2 Press the G button and then D / T u n i n g. 3 Press the G button and then D / E button to select the S e t u p Auto Tuning Manual Tuning Programme Edit Favourite Programme To Set E button to select M a n u a l E button to select S t o r a g e.
WATCHING TV /PROGRAMME CONTROL FINE TUNING Normally fine tuning is only necessary if reception is poor. 1 Press the M E N U button and then D / S e t u p menu. 2 Press the G button and then D / T u n i n g. E button to select M a n u a l 3 Press the G button and then D / E E button to select the Setup Auto Tuning Manual Tuning Programme Edit Favourite Programme 5 Press the G button and then best picture and sound. D / E To Set button to select F i n e.
WATCHING TV /PROGRAMME CONTROL PROGRAMME EDIT This function enables you to delete or skip stored programmes. Also you can move some stations to other programme numbers or copy a blank station data into the selected programme number. 1 Press the M E N U button and then D / S e t u p menu. E E button to select the button to select P r o g r a m m e 2 Press the G button and then D / E d i t. 3 Press the G button to display the Programme edit menu. A Deleting a programme 1.
WATCHING TV /PROGRAMME CONTROL FAVOURITE PROGRAMME This function lets you select your favourite programmes directly. Setup 1 Press the M E N U button and then D / S e t u p menu. E button to select the Auto Tuning Manual Tuning Programme Edit Favourite Programme E button to select F a v o u r i t e 2 Press the G button and then D / P r o g r a m m e. 3 Press the G button. 4 Press the D / 5 Select a desired programme with the F / G button or NUMBER buttons.
WATCHING TV /PROGRAMME CONTROL SELECTING THE PROGRAMME LIST You can check which programmes are stored in the memory by displaying the programme list. A Displaying programme list Press the L I S T button to display the Programme list menu. The programme list appears on the screen. One programme list contains ten programmes as shown. ! NOTE a. You may find some blue programmes. They have been set up to be skipped by auto programming or in the programme edit mode. b.
PICTURE CONTROL WATCHING PIP (PICTURE-IN-PICTURE) PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other source will show a smaller inset image. PIP function is available in the RGB-PC, DVI input only.
PICTURE CONTROL PICTURE SIZE (ASPECT RATIO)CONTROL You can watch the screen in various picture formats; 1 6 : 9 , O r i g i n a l, 4 : 3, 1 4 : 9, Z o o m 1 / 2 and J u s t S c a n. Just Scan works in the following mode: Component (720p/1080i/1080p), HDMI (720p/1080i/1080p) If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible. You can adjust the enlarge proportion using D / E button. This function works in the following signal.
PICTURE CONTROL • Zoom1 The following selection will allow you to view the picture without any alteration, while filling the entire screen. However, the top and bottom of the picture will be cropped. • Just Scan Following Selection will lead to you view the picture of best quality without loss of original picture in high resolution image. Just Scan Zooml DE • Zoom2 Choose Zoom 2 when you wish the picture to be altered, both horizontally extended and vertically cropped.
PICTURE CONTROL PRESET PICTURE SETTINGS Picture Mode-Preset Picture Mode adjusts the set for the best picture appearance. Select the preset value in the P i c t u r e M o d e menu based on the programme category. Vivid, Standard, Cinema, Sport and Game are programmed for optimum picture reproduction at the factory and cannot be changed. 1 Press the M E N U button and then D / P i c t u r e menu. 2 Press the G button and then D / M o d e.
PICTURE CONTROL MANUAL PICTURE ADJUSTMENT Picture Mode-User Mode Backlight Contrast Brightness Colour Sharpness Tint Adjust the brightness of LCD panel to control the brightness of the screen. Adjusts the difference between light and dark levels in the picture. Increases or decreases the amount of white in the picture. Adjusts intensity of all colours. Adjusts the level of crispness in the edges between the light and dark areas of the picture. The lower the level, the softer the image.
PICTURE CONTROL Auto Colour Tone Control(Cool/Medium/Warm) To initialize values (reset to default settings), select the Cool option. Choose one of three automatic colour adjustments. Set to warm to enhance hotter colours such as red, or set to cool to see less intense colours with more blue. This menu is activated after selecting “User1” or “User2” in the Picture Mode. 1 Press the M E N U button and then D / the P i c t u r e menu. 2 Press the G button and then D / T e m p e r a t u r e.
PICTURE CONTROL Colour Tone - User Mode To adjust red, green, blue to any colour temperature you prefer. This menu is activated after selecting “User1” or “User2” in the Picture Mode. Picture 1 Press the M E N U button and then D / P i c t u r e menu. 2 Press the G button and then D / T e m p e r a t u r e. E button to select C o l o u r 3 Press the G button and then D / E button to select U s e r. 4 Press the G button and then D / or B l u e.
PICTURE CONTROL - PICTURE IMPROVEMENT TECHNOLOGY XD is LG electronic's unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm. It is not possible to use this function in RGB-PC/DVI input. This menu is activated after selecting the U s e r 1 or U s e r 2 of P i c t u r e M o d e. 1 Press the MENU button and then D / P i c t u r e menu. E button to select the 2 Press the G button and then D / E button to select X D.
PICTURE CONTROL ADVANCED - GAMMA High gamma values display whitish images and low gamma values display high contrast images. It is not possible to use this function in RGB-PC/DVI input. Picture 1 Press the M E N U button and then D / P i c t u r e menu. 2 Press the G button and then D / E button to select A d v a n c e d. 3 Press the G button and then D / E button to select G a m m a. 4 Press the G button and then D / M e d i u m or H i g h .
PICTURE CONTROL PICTURE RESET Returns to the default factory setting for Picture Mode, Colour Temperature, XD, Advanced, Aspect Ratio. Picture 1 Press the M E N U button and then D / P i c t u r e menu. 2 Press the G button and then D / R e s e t. 3 Press the G button to initialize the adjusted value.
PICTURE CONTROL SCREEN SETUP FOR PC MODE Auto Configure (RGB [PC] mode only) Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, your set is functioning properly but needs further adjustment. Auto configure This function is for automatic adjustment of the screen position, clock, and phase. The displayed image will be unstable for a few seconds while the auto configuration is in progress. 1.
PICTURE CONTROL Manual Configure (Adjustment for screen Phase, Clock, Position) (RGB [PC] mode only) If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. To correct the screen size, adjust C l o c k. It’s not available to use Phase, Clock function in COMPONENT (480i/480p/576i/576p/720p/1080i/1080p), HDMI (480p/576p/720p/1080i/1080p).
PICTURE CONTROL Selecting Resolution To view a normal picture, match the resolution of RGB mode and selection of Resolution. This function works in the following mode: RGB-PC input mode. Picture 1 Press the M E N U button and then use D / P i c t u r e menu. 2 Press the G button and then use D / E button to select S c r e e n. 3 Press the G button and then use D / Resolution E button to select Press the G button and then use D / desired Resolution.
SOUND CONTROL PRESET SOUND SETTINGS-SOUND MODE You can select your preferred sound setting; S R S T S X T , C l e a r V o i c e , S t a n d a r d , M u s i c , C i n e m a , S p o r t or G a m e and you can also adjust the frequency of the equalizer. Sound Mode lets you enjoy the best sound without any Special adjustment as the sets the appropriate sound options based on the programme content.
SOUND CONTROL AUTO VOLUME LEVELER Auto Volume automatically remains on the same level of volume if you change programmes. 1 Press the M E N U button and then D / A u d i o menu. E button to select the 2 Press the G button and then D / V o l u m e. E button to select A u t o 3 Press the G button and then D / E Audio Sound Mode Auto Volume Balance TV Speaker G 0 V Off On button to select O n or O f f.
SOUND CONTROL I/II Stereo/Dual Reception When a programme is selected, the sound information for the station appears with the programme number and station name. 1 Press the I / I I button and then D / E button. Broadcast On Screen Display Mono MONO Stereo STEREO Dual DUAL I, DUAL II, DUAL I+II A Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of sound is improved. To switch back to stereo.
TIME SETTING CLOCK SETUP You must set the time correctly before using on/off timer function. If current time setting is erased by a power failure or the set is unplugged, reset the clock. 1 Press the M E N U button and then D / T i m e menu. 2 Press the G button and then D / E button to select C l o c k. 3 Press the G button and then D / E button to set the hour. 4 Press the G button and then D / E button to set the minute.
TIME SETTING SLEEP TIMER SETTING You do not have to remember to switch the set off before you go to sleep. The sleep timer automatically switches the set off after the preset time has elapsed. Time 1 Press the M E N U button and then D / T i m e menu. 2 Press the G button and then D / T i m e r. E button to select S l e e p 3 Press the G button and then D / E button to set the minute.
OPTION SETTING ON-SCREEN MENU LANGUAGE SELECTION Installation guide menu appears on set screen when it is turned on for the first time. Press the D / E/ F / G button and then, O K button to select your desired language. 1 Language PIP Key Lock Set ID DDC-CI Power Indicator Factory Reset * If you want to change Language selection Press the M E N U button and then use D / select the O P T I O N menu. 1 Press the G button and then use D / L a n g u a g e.
OPTION SETTING KEY LOCK The set can be set so that the remote control is needed to control it. This feature can be used to prevent unauthorized viewing. This set is programmed to remember which option it was last set to even if you turn the set off. 1 Press the M E N U button and then D / O p t i o n menu. E button to select the 2 Press the G button and then D / E button to select K e y L o c k. 3 Press the G button and then D / E button to select O n or O f f.
OPTION SETTING DDC CI(Only RGB, DVI mode) DDC/CI (Display Data Channel Command Interface) is a communication protocol for communications between PC and set. DDC/CI makes it possible to adjust and setup detailed functions on PC instead of the set OSD. Set can be adjusted with PC by connecting communication between PC and set when DDC/CI is ON, and set cannot be adjusted with PC because communication between PC and set is disconnected when DDC/CI is OFF.
OPTION SETTING POWER INDICATOR Option It helps you control LED when power is turned on. 1 Press the M E N U button and then D / O p t i o n menu. E button to select the 2 Press the G button and then D / indicator. E button to select P o w e r 3 Press the G button and then D / E Language PIP Key Lock Set ID DDC-CI Power Indicator Factory Reset DE F G V Off On V Off On G O K RETURN button to select O n or O f f.
TELETEXT This feature is not available in all countries. Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programmes, share prices and many other topics. The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number.
TELETEXT TOP TEXT The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field indicates the next block. A Block / group / page selection 1 2 3 4 With the blue button you can progress from block to block. Use the yellow button to proceed to the next group with automatic overflow to the next block. With the green button you can proceed to the next existing page with automatic overflow to the next group.
TELETEXT SPECIAL TELETEXT FUNCTIONS A TIME When viewing a TV programme, press this button to display the time at the top right hand corner of the screen. Press this button again to remove the display. In the teletext mode, press this button to select a sub page number. The sub page number is displayed at the bottom of the screen. To hold or change the sub page, press the RED/GREEN, P R D / E or NUMBER buttons. Press again to exit this function. A SIZE Selects double height text.
APPENDIX TROUBLESHOOTING The operation does not work normally. Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the set. A Ensure that the batteries are installed with correct polarity (+ to +, - to -). A Ensure that the correct remote operating mode is set: TV, VCR, etc. A Install new batteries.
APPENDIX The audio function does not work. A Picture OK & No sound A A A No output from one of the speakers Unusual sound from inside the product Press the VOL F / G button. Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly? A Adjust Balance in menu option. A A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a problem with the product.
APPENDIX ‘Unknown Product’ message appears when the product is connected. A Install the product driver, which is provided with the product, or download it from the web site. (http://www.lge.com) A See if the plug_&_play function is supported by referring to the video card user’s guide. Did you install the driver? After-image appears on the product. After-image appears when the product is turned off. A If you use a fixed image for a long time, the pixels may be damaged quickly.
APPENDIX MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new set. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1 To keep the dust off your screen for a while, wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dishwashing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
APPENDIX PRODUCT SPECIFICATIONS LCD Panel Video Signal Screen Type 23 inches Wide (584.2 mm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size : 584.2 mm Pixel Pitch 0.265(H) x 0.265(V) mm Max.
APPENDIX PRODUCT SPECIFICATIONS LCD Panel Video Signal Screen Type 27 inches Wide (686 mm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size: 686 mm Pixel Pitch 0.3114(H) x 0.3114(V) mm Max.
APPENDIX IR CODES 1. How to Connect A Connect your wired remote control to the Remote Control port on the set. 2. Remote Control IR Codes A Output waveform Single pulse, modulated with 37.
APPENDIX (Hexa) Code Function Note Code Function 79 ARC R/C Button 09 MUTE R/C Button 0B INPUT R/C Button 53 LIST R/C Button (Hexa) Note 08 POWER R/C Button (Power On/Off) 10 ~ 19 Number Key 0 ~ 9 R/C Button 43 MENU R/C Button 1A Q.
APPENDIX EXTERNAL CONTROL THROUGH RS-232C Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the set’s functions externally. Connect the serial port of the control device to the RS-232C jack on the set back panel.RS-232C connection cables are not supplied with the set. RS-232C Setup N HDMI IN RS-232C IN (CONTROL) N Type of Connector; D-Sub 9-Pin Male No.
APPENDIX RS-232C Configurations 7-Wire Configurations (Standard RS-232C cable) RXD TXD GND DTR DSR RTS CTS PC SET 2 3 5 4 6 7 8 3 2 5 6 4 8 7 D-Sub 9 D-Sub 9 TXD RXD GND DSR DTR CTS RTS 3-Wire Configurations(Not standard) RXD TXD GND DTR DSR RTS CTS PC SET 2 3 5 4 6 7 8 3 2 5 6 4 7 8 D-Sub 9 D-Sub 9 TXD RXD GND DTR DSR RTS CTS Set ID Option - Use this function to specify a set ID number. - Refer to ‘Real Data Mapping 1’. See page 67.
APPENDIX Command Reference List COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Power k a 00 ~ 01 02. Aspect Ratio k c Refer to p.65 COMMAND1 COMMAND2 DATA (Hexadecimal) 14. Colour Temperature k u Refer to p.66 15. Red Adjustment k v 00 ~ 3C 03. Screen Mute k d 00 ~ 01 16. Green Adjustment k w 00 ~ 3C 04. Volume Mute k e 00 ~ 01 17. Blue Adjustment k $ 00 ~ 3C 05. Volume Control k f 00 ~ 64 18. Abnormal Status k z FF 06. Contrast k g 00 ~ 64 19.
APPENDIX 0 5 . Volume Control (Command: k f) 0 1 . Power (Command: k a) To control Power On/Off of the TV. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off Data 01 : Power On Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x] To show Power On/Off. To adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission [k][f][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 Refer to ‘Real data mapping 1 ’. See page 67.
APPENDIX 15. Red Adjustment (Command: k v) 10. Sharpness (Command: k k) To adjust the screen sharpness. To adjust red in colour temperature. You can also adjust sharpness in the Picture menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Transmission [k][v][ ][Set ID][ ][Data][Cr] Data Min: 00 ~ Max: 3C Data Min : 00 ~ Max : 64 Refer to ‘Real data mapping 2’. See page 67. Refer to ‘Real data mapping 1 ’. See page 67.
APPENDIX 22. Channel Skip(Command: m b) 19 . Auto Configure (Command: j u) To adjust picture position and minimize image G To set skip status for the current Programme. shaking automatically. It works only in RGB (PC) mode. Transmission [m][b][ ][Set ID][ ][Data][Cr] Data 00 : Skip Transmission [j][u][ ][Set ID][ ][Data][Cr] 01 : Add Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x] Data 01: To set Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x] 23. K e y C o d e (Command: m c) 2 0 .