ENGL ISH ESPA ÑOL INSTALLATION MANUAL GAS COOKTOP Please read this guide thoroughly before installation. P/No.: MFL62725502 www.lge.
INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLATION IN THE COMMONWEALTH OF MASSACHUSETTS • This product must be installed by a licensed plumber or gas fitter. • A flexible gas connector, when used, must not exceed 3 feet in length. • When using ball type gas shut-off valves, they shall be the T-handle type. FOR YOUR SAFETY WARNING : If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
INSTALLATION INSTRUCTIONS ENGL ISH INSTALLATION SAFETY INSTRUCTIONS BEFORE YOU BEGIN Remove all tape and packing materials before using the cooktop. Dispose all plastic bags after unpacking the cooktop. Never allow children to play with packing materials. IMPORTANT SAFETY INSTRUCTIONS Read these instructions completely and carefully. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.
INSTALLATION INSTRUCTIONS INSTALLATION SAFETY INSTRUCTIONS (continued) • The ventilating hood must be constructed of sheet metal not less than 0.0122” thick. Install above the cooktop with a clearance of not less than 1/4” between the hood and the underside of the combustible material or metal cabinet. The hood must be at least as wide as the appliance and centered over the appliance. Clearance between the cooking surface and the ventilation hood surface MUST NEVER BE LESS THAN 24 INCHES.
INSTALLATION INSTRUCTIONS Provide enough clearances between the cooktop and adjacent combustible surfaces. These dimensions must be met for safe use of your cooktop. The location of the electrical outlet and pipe opening may be adjusted to meet specific requirements. The cooktop may be placed with 2 3/4” clearance to the back wall. 1. MAINTAIN THE FOLLOWING MINIMUM CLEARANCE DIMENSIONS 13˝MAX. Depth of unprotected overhead cabinets 3. RECOMMENDED GAS SUPPLY LOCATION FROM BACKWALL 1” Min.
INSTALLATION INSTRUCTIONS INSTALLING THE COOKTOP UNIT 1. LOCATE ELECTRICAL OUTLET AND GAS SHUT-OFF VALVE BENEATH CABINET NEVER RE-USE OLD FLEX CONNECTORS. Electrical outlet 12˝ below countertop 4 INSTALL THE RETAINER BRACKETS Install the retainer brackets to the bottom of the cooktop unit. then snug the bolts against the bottom of the countertop as shown Shut-Off valve Install a manual shut-off valve in the gas line in an easily accessible location outside the cooktop.
INSTALLATION INSTRUCTIONS ENGL ISH 1. PROVIDE ADEQUATE GAS SUPPLY This cooktop is designed to operate at a pressure of 5” of water column on natural gas or 10” of water column on LP, propane or butane gas. Make sure you are supplying your cooktop with the type of gas for which it is designed. This cooktop is convertible for use on natural or propane gas. When using this cooktop on LP gas, conversion must be made by a qualified LP installer before attempting to operate the cooktop on that gas.
INSTALLATION INSTRUCTIONS FLEXIBLE CONNECTOR HOOKUP Pressure regulator Adapter Gas Flow into Range Flex connector (6 ft. max. ) Adapter Installer: Inform the consumer of the location of the gas shut-off valve.
INSTALLATION INSTRUCTIONS ENGL ISH 3. ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS 120 Volt, 60 Hertz, properly grounded dedicated circuit protected by a 15 A or 20 A circuit breaker or time delay fuse. GROUNDING IMPORTANT: FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
INSTALLATION INSTRUCTIONS 3. ELECTRICAL CONNECTIONS CAUTION The customer should have the circuit checked by a qualified technician to make sure the receptacle is correctly grounded. DO NOT use an adapter plug because disconnecting of the power cord places undue strain on the adapter and causes eventual failure of the adapter ground terminal. The customer must have the two-prong wall receptacle replaced with a three-prong (grounding) receptacle by a qualified technician before using this cooktop. 4.
INSTALLATION INSTRUCTIONS ENGL ISH 5. ASSEMBLE THE SURFACE BURNERS Make sure the hole in the burner head is positioned over the electrode. CAUTION DO NOT operate the burners without all parts in place. Hole Place the burner caps and heads on the cooktop. Make sure that the caps and heads are placed in the correct locations. Electrode Extra large burner (Center) head and cap Small burner head and cap Medium burner head and cap Lrage burner head and cap 6.
INSTALLATION INSTRUCTIONS 7. ADJUST THE SURFACE BURNER LOW FLAME (SIMMER) SETTING For all surface burners except for the center burner 1. Light all surface burners except for the center burner. 2. Turn the knob on the burner being adjusted to LO (LOW). 3. Remove knob. 4. Insert a small, flat bladed screwdriver into the valve stem as shown in Fig.2. 5. Turn the adjustment screw until the flame reaches the desired size. 6. Replace the knob. Center adjustment screw Fig. 2 7. Test The Flame Stability.
INSTALLATION INSTRUCTIONS ENGL ISH WHEN ALL HOOKUPS ARE COMPLETE Make sure all controls are left in the off position. Make sure the flow of combustion and ventilation air to the cooktop is unobstructed. CONVERTING TO LP GAS (OR CONVERTING BACK TO NATURAL GAS FROM LP) This cooktop leaves the factory set for use with natural gas. When converting to LP gas, the conversion must be performed by a qualified LP gas installer. The conversion instructions and LP orifices are supplied with your cooktop.
Memo 14
BEFORE YOU BEGIN Read these instructions completely and carefully. Note to Installer:Leave these instructions with the appliance after installation is completed. Installation of this cooktop must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest edition. This cooktop has been design-certified by CSA International according to ANSI Z21.1, latest edition and Canadian Gas Association according to CAN/CGA-1.1 latest edition.
