RELEASING THIS DRAWING WITHOUT PERMISSION LG Electronics SHOULD BE ACCUSED ACCORDING TO THE LAWS AND COMPANY RULES. MFL70280504 이 도면은 LG전자의 자산으로 불법 유출시 관계법과 회사규정에 의해 처벌됨. WORK SEC. 가 BRAND 04 LG 나 MODEL 다 P/NO. MFL70280504 WTP20WY 216 가 가 PRINTING DEGREE EXTERIER INTERIER 1 1 LG MODEL 명 MATERIAL AND PRINTING DESCRIPTION 모조지 80g OFFSET 인쇄 SUFFIX F8K5XNK3 LANGUAGE PAGE REMARK EN 44 W-module (W) ABWREAP << 주기 >> 1. 재질 : 모조지 80g 2.
OWNER'S MANUAL WASHING MACHINE Before beginning installation, read these instructions carefully. This will simplify installation and ensure that the product is installed correctly and safely. Leave these instructions near the product after installation for future reference. WTP20WY MFL70280504 Rev.00_080117 www.lg.com Copyright © 2017 LG Electronics Inc. All Rights Reserved.
TABLE OF CONTENTS This manual may contain images or content different from the model you purchased. This manual is subject to revision by the manufacturer. SAFETY INSTRUCTIONS......................................................... 4 IMPORTANT SAFETY INSTRUCTIONS.....................................................4 INSTALLATION........................................................................ 10 Parts................................................................................................
SAFETY INSTRUCTIONS EN The following safety guidelines are intended to prevent unforeseen risks or damage from unsafe or incorrect operation of the appliance. The guidelines are separated into ‘WARNING’ and ‘CAUTION’ as described below. This symbol is displayed to indicate matters and operations that can cause risk. Read the part with this symbol carefully and follow the instructions in order to avoid risk.
EN Installation •Never • attempt to operate the appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug. •This • appliance should only be installed and transported by two or more people holding the appliance securely. •Do • not install the appliance in a damp and dusty place.
EN •If • the power cord is damaged or the hole of the outlet socket is loose, do not use the power cord and contact an authorized service centre. •This • appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the appliance, in such a way that a full opening of the appliance door is restricted. •This • appliance must be grounded (earthed via the power cord).
EN Operation •Do • not use a sharp object like drill or pin to penetrate, modify or disassemble the unit. •Do • not repair or replace any part of the appliance. All repairs and servicing must be performed by qualified service personnel unless specifically recommended in this Owner’s Manual. Use only authorized factory parts. •Use • a new hose or hose-set supplied with the appliance. Reusing old hoses can cause a water leak and subsequent property damage.
EN •Do • not use flammable gas and combustible substances (benzene, gasoline, thinner, petroleum, alcohol, etc.) near the appliance. •If • the drain hose or inlet hose is frozen during winter, use it only after thawing. •Keep • all washing detergents, softener and bleach away from children. •Do • not touch the power plug or the appliance controls with wet hands. •When • pulling out the power plug from an outlet, hold the power plug, not the cable.
EN Maintenance •Securely • plug the power plug in the socket outlet after completely removing any moisture and dust. •Disconnect • the power cord before cleaning the appliance. •Never • unplug the appliance by pulling on the power cable. Always grip the power plug firmly and pull straight out from the socket outlet. •Do • not spray water inside or outside the appliance to clean it. Disposal •Before • discarding an old appliance, unplug it.
INSTALLATION EN Parts 5 6 1 2 3 4 7 8 1 Door 5 Water Supply Hose 2 Drum 6 Power Plug 3 Control Panel 7 Water Drain Hose 4 Drawer 8 Leveling Feet 10
EN Accessories Water supply hose (for cold water) Connecting supply hose Water drain hose Water supply hose connector Water drain hose connector Anti-slip sheets (2 EA) Detergent measuring cup Brackets (front) (2 EA) Brackets (back) (2 EA) Spanner * Screws Type A (37 EA) Type B (5 EA) Type C (11 EA) Cable ties (2 EA) Band clamps (3 EA) Remote control (some models only) * Type A : long sheet metal screw, Type B : short sheet metal screw, Type C : machine screw NOTE ••Different accessories ma
EN Installation Place Requirements Location 135 cm 123 cm 0.5 cm 125 cm 2 cm 114 cm *125 cm 10 cm 5 cm 60 cm 5 cm *125 cm: minimum space for installation Level floor : Allowable slope under the entire appliance is 1°. Power outlet : Must be within 1.5 meters of either side of the location of the appliance. ••Do not overload the outlet with more than one appliance. Additional Clearance : 5 cm at the sides and 10 cm behind the unit.
EN Stacking Mini Washer Type 1. Where the bottom part of the Main Washer is silver in color. ••First assemble the stacking holder using 2 type A screws included in the accessory box of the Mini Washer, then each bracket using 7 type A screws included in the accessory box of the Mini Washer. Brackets (front) Brackets (back) 2 1 Brackets (front) Brackets (back) 3 ••The error message appears on the display, if the stacking holder is not attached to the bottom of the Main Washer.
EN 3 Pull and save the foam block for future use. ••If the washing machine must be moved in the future, the foam block will help prevent damage to the washing machine during transportation. 6 Carefully place the Main Washer on top of Mini Washer. ••Make sure the 4 legs are totally wound in and the holes of Mini Washer align with the holes of Main Washer. Washer leg Washer leg NOTE ••To prevent damage, do not remove the foam block until Mini Washer is at the final location.
EN Connecting the Supply Hose ••Water supply pressure must be between 0.1 MPa and 0.8 MPa (100 ~ 800kPa). ••Do not overtighten the water supply hose. ••If the water supply pressure is more than 0.8 MPa, a decompression device should be installed. ••Periodically check the condition of the hose even after installation and replace the hose if necessary. ••Contact the service centre if there is no rubber seal fitted to the hose ends.
EN Connecting the Cold Supply Hoses to Both Washing Machines 1 Connect one end of the cold water supply hose connector to the cold water supply hose of the Main Washer first. Open the accessory package for the Mini Washer installation accesories. 3 Connect the additionally provided water supply hose of Main Washer to the cold water supply hose connector and cold water tap.
EN Installing the Drain Hose Using the Drain Hose Connector ••The drain hose should not be placed higher than 100 cm above the floor. Water in the appliance may not drain or may drain slowly. 1 Connect the drain hose of Main Washer and Mini Washer to the drain connector. 2 Insert the included band clamps on to the ends of the two drain hoses. 3 Push the drain hoses firmly onto the drain connector. 1 Insert the band clamp onto the drain hose elbow.
EN Leveling the Appliance Using Anti-Slip Sheets (Optional) If the floor is uneven, turn the adjustable feet as required (Do not insert pieces of wood etc. under the feet). Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level (Use a spirit level). ••Once the appliance is level, tighten the lock nuts up towards the base of the appliance. All lock nuts must be tightened.
OPERATION Using the Appliance 1 2 EN 5 Choose the desired washing cycle. ••Press the cycle button repeatedly until the desired cycle is selected. 6 Begin cycle. ••Press the Start/Pause button to begin the cycle. The Mini washer will agitate briefly without water to measure the weight of the load. If the Start/Pause button is not pressed within 15 minutes, the washing machine will shut off and all settings will be lost. 7 To Add softener.
EN Sorting Laundry 1 3 Look for the care label on your clothes. ••This will tell you about the fabric content of your garment and how it should be washed. ••Symbols on the care labels. Wash temperature Normal machine wash Caring before loading. ••Do not wash items that contain support or memory wire such as Bras as it may damage other clothes as well as the washing machine and cause noise and vibration. ••Check all pockets to make sure that they are empty.
EN Closing the Door and Drawer 1 Gently push down on the Mini Washer’s Lid until it clicks. 2 Push the drawer in until it has completely closed. CAUTION ••Do not let your hands get stuck between the door and the washing machine, as this can cause injury. ••Forcing the drawer or the Lid to open can cause parts to be damaged and safety problems. ••Closing the drawer before having closed the Lid completely may scratch the Lid glass.
EN Adding Cleaning Products Adding Detergent Detergent Dosage Measure the detergent with the detergent dispenser and pour it into the tub. ••Detergent should be used according to the instruction of the detergent manufacturer and selected according to type, colour, soiling of the fabric and washing temperature. ••If too much detergent is used, too many suds can occur and this will result in poor washing results or cause heavy load to the motor.
EN Adding Softeners Adding Fabric Softener CASE 1. When the machine chimes: 1 Press Start/Pause to pause the cycle. ••It can be paused by pressing the Start/ Pause button of the Mini Washer or by using the remote control. 2 Slide open the drawer, open the door, and add the liquid fabric softener. 3 Close the door, slide the drawer closed, and press Start/Pause to restart the cycle. NOTE Adding Water Softener ••A water softener, such as anti-limescale (e.g.
EN Control Panel 1 4 2 5 3 1 Power Button ••Press the Power button to turn the washing machine on, or off if washing hasn't commenced. 2 Display ••The display shows the cycle status and estimated time remaining. •• : Drawer lock indicator •• : Wi-Fi connect indicator •• : Remote start indicator 3 Programme Button ••Programmes are available according to laundry type. ••In order to use the Download Cycle function, refer to SMART FUNCTIONS.
EN Programme Table Washing Programme Programme Light Soil Speed Wash Active Wear Tub Clean Hand Wash Rinse+Spin Description Note •• Pressing the Start/Pause button Use this programme to without selecting a programme will wash lightly soiled normal cause the Normal programme to items, except delicate begin immediately using the default fabrics such as wool or silk. settings. Use this programme to speed up the washing time •• Use very little detergent in this for small loads and lightly programme.
EN Option Programme Child Lock Spin Only Use this option to disable the controls. This feature can prevent children from changing cycles or operating the appliance. Use this option to spin a hand washed load that may not have been washed in the machine. Extra Rinse Use this option to increase the number of rinsing programmes. 1 Press the Power button. 2 Select a washing programme. 3 4 26 Press the Extra Rinse button to set the amount of Rinses required.
SMART FUNCTIONS Using SmartThinQ Application NOTE Installing SmartThinQ Search for the LG SmartThinQ application from the Google Play Store or Apple App Store on a smart phone. Follow instructions to download and install the application. Wi-Fi Function ••For appliances with the or EN logo Washer Cycle (Remote Start, Download Cycle) Set or download any preferred cycle and operate by remote control.
EN Using Washer Cycle Remote Start Use a smart phone to control your appliance remotely. You can also monitor your cycle operation so you know how much time is left in the cycle. To Use Remote Start: 1 Press the Power button. 2 Put the laundry in drum. 3 Press and hold Remote Start button for 3 seconds to enable Remote Start function. 4 Start a cycle from the LG Smart ThinQ application on your smart phone.
EN Using Smart Diagnosis™ Smart Diagnosis™ Through the Customer Information Centre Use this function if you need an accurate diagnosis by an LG Electronics customer information centre when the appliance malfunctions or fails. Use this function only to contact the service representative, not during normal operation. 1 Press the Power button after opening the drawer on Mini Washer. 2 When instructed to do so by the call centre, place the mouthpiece of your phone close to the Smart Diagnosis™ icon.
MAINTENANCE WARNING ••Unplug the washing machine before cleaning to avoid the risk of electric shock. Failure to follow this warning may result in serious injury, fire, electric shock, or death. ••Never use harsh chemicals, abrasive cleaners, or solvents to clean the washing machine. They may damage the finish. Cleaning the Washing Machine Care After Wash ••After the cycle is finished, wipe the door and the inside of the door seal to remove any moisture. ••Leave the door open to dry the drum interior.
EN Cleaning the Drum Cleaning the Water Inlet Filter Use the Tub Clean option to keep the drum clean. ••Turn off the water supply tap if the washing machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain (gully) in the immediate vicinity. •• icon may blink on the display when the water pressure is weak or an inlet filter is clogged with dirt. Clean the inlet filter.
EN Cleaning the Lint Filter The Lint filter is an important part for an efficient washing performance result, so it needs special care from you. It is recommended that the filter be cleaned regularly. 1 Squeeze the side tabs and lift out the filter. Caution on Freezing During Winter ••When frozen, the product does not operate normally. Make sure to install the product where it will not freeze during winter.
EN How to Handle Freezing Step 1. When the Door is Frozen ••Thaw out the door using a hot water cloth. Step 2. When the Water Supply Hose is Frozen •• icon may blink on the display when water supply problems occur, take the following measures. −−Take out water supply hose and connect to the tap and check that water comes from the tap and supply hose. −−Turn off the tap, and thaw out the tap and both connection areas of supply hose of the product using a hot water cloth.
TROUBLESHOOTING EN The appliance is equipped with an automatic error-monitoring system to detect and diagnose problems at an early stage. If the appliance does not function properly or does not function at all, check the following before you call for service: Diagnosing Problems Symptoms Reason The drawer does not open. Power failure, or the power cord was pulled out during washing. - The machine may not be level Draining starts when pressing Start/ Pause button.
EN Symptoms Staining Water leaking Wrinkling Reason Solution ••Always wash dark colors separately from light colors and whites to prevent Clothes were not properly discoloration. sorted. not mix softener and detergent -Wrong detergents are added. ••Do together. Add softener only when the softener alert chime indicates to do so. Supply hose connection is ••Check hoses and drain hose connectors loose at the tap, washing for leaks, cracks and splits. machine, or drain hose ••Tighten hose connections.
EN Symptoms Reason Control panel has powered off due to inactivity. Washing machine is unplugged. Water supply is turned off. Washing machine will not operate. 36 Solution ••This is normal. Press the Power button to turn the washing machine back on. ••Make sure the power cord is plugged securely into a working outlet. ••Turn the cold water tap fully on. ••Make sure the cycle was set correctly, Controls are not set properly. close the door and press the Start/Pause button.
EN Symptoms Reason Solution Washing machine is not filling properly. ••Make sure the inlet filter on the fill valve is not clogged. Refer to the filter cleaning instructions. • • Check that the supply hose is not kinked Supply hoses may be kinked. or clogged. • • Make sure that the cold water tap is Insufficient water supply. turned on all the way. ••The washing machine will not operate if the lid is open. Close the lid and make door and drawer are open.
EN Error Messages Symptoms Reason Solution ••Close the drawer and press Start/Pause button to start the cycle. ••If the drawer is closed and the drawer lock error message is displayed, call for service. ••Open the drawer and make sure the latch area is free of clothing or other obstructions. Door is not closed properly. ••Close the door, shut the drawer, and press Start/Pause to start the cycle. ••If the door is closed and the door error message is displayed, call for service.
EN Symptoms Reason Solution ••The automatic attempt to rebalance the load was not successful. The cycle has been paused to allow the load to be manually adjusted. • • Add more items to allow the washing The load is too small. machine to balance the loads. Heavy articles are mixed with ••Wash articles of somewhat similar lighter items. weight. • • Manually redistribute the load if articles The load is out of balance. have become tangled. UE rebalancing operation was not successful. Control error.
Memo
Memo
Memo