Model #710 WATCH THE VIDEO ™ Owner’s Manual VISIT OUR WEBSITE: WWW.LIBERTYGARDENPRODUCTS.COM OR CALL US TOLL FREE AT 1-866-820-5805, MONDAY - FRIDAY 9 A.M. - 5 P.M. EST LIBERTY GARDEN PRODUCTS, INC.
PRE-ASSEMBLY Estimated Assembly Time : 10 minutes (not including mounting the hose reel) TOOLS REQUIRED: Hammer Drill Adjustable Wrench AA Electric Drill Phillips screwdriver or bit for an electric drill AA. Allen wrench (Supplied) 7/16 in. and 3/8 in. Socket and Socket wrench Stud Finder HARDWARE INCLUDED BB BB. Allen bolts (3) CC DD CC. Lock nuts (3) DD. Allen screw (1) Note: Hardware not shown to actual size. The wall mounting hardware is NOT included with this unit.
INSTALLATION This hose reel must be mounted to a solid masonry wall or to wall studs TIP: Remember to use the correct size and quantity of hardware to properly support the total weight of the unit. A standard 100' length of garden hose weighs approximately 15 lbs. Filled with water, the additional weight can exceed 20 lbs. The mounting hardware must be able to support the combined weight of the unit, garden hose, plus water. 1.
ASSEMBLY 1 2 Attach the hose reel (D) to the base shelf (C) by hanging the reel on the small slot located at the front of the base. Line up the holes in the hose reel (D) with the base shelf (C) and insert long Allen bolts (BB) C FIGURE 2 C BB FIGURE 1 3 D D C FIGURE 3 Tighten Allen bolts (BB) with the supplied Allen wrench (AA) at the same time using fingers screw on lock nuts (CC) to secure base shelf (C) to hose reel (D) CC Pliers (not included) may be needed to hold and tighten lock nuts.
ASSEMBLY 4 Align the holes in the crank handle (A) with the crank handle shaft on the hose reel (D). Insert the short Allen screw (DD) into the crank handle and tighten with supplied Allen wrench (AA) D FIGURE 4 AA DD A 5 6 Attach leader hose (B) to swivel connector on the hose reel (D). Attach end of leader hose to water source. Attach your garden hose to the hose connector on the hose reel (D). The hose is now ready to wind around the spool. The Navigator holds up to 125 ft. of 5/8” garden hose.
OPERATING INSTRUCTIONS 1 2 Pull up on handle knob located on the base shelf (C) then rotate hose reel (D) to one of the eight locking positions. FIGURE 1 C Pull up on the handle knob located on the base shelf (C) and turn the locking pin to the up position. The Navigator rotating hose reel will now turn a full 360 degrees. D FIGURE 2 C FIGURE 3 C 3 4 Release the handle on the base shelf (C) and lock unit into one of the desired positions. Your Navigator rotating hose reel is now ready for use.
CARE INSTRUCTIONS Your hose reel is manufactured with the finest quality components available. This product will give you many seasons of reliable and functional hose storage. All components are manufactured to rigorous quality standards not common in other consumer grade hose reels available today. As with any steel product, there is always the chance for rust developing over time.
TROUBLE SHOOTING GUIDE Problem: Swivel head is not rotating, causing the leader hose to kink up. Solution: Remove leader hose and turn the square head of the swivel several times; apply lubricant. Problem: Your new Liberty hose reel is leaking at the swivel. Solution: Apply Teflon/Plumber's Tape on the threads or/and make sure fixtures are tightened. It is normal for the swivel to leak slightly until the O-rings are wet and have seated.
LIBERTY GARDEN PRODUCTS LIMITED WARRANTY (Effective October 13, 2016) This limited warranty is applicable to each original end-customer (hereinafter “Customer”) purchasing the model the model 710 decorative Navigator rotating hose reel consisting of the structural metal frame and spool (hereinafter the “Structural Frame”) and various other non-frame components (hereinafter the “Non-Frame Parts”) sold by Liberty Garden Products, Inc. (hereinafter “Company”) for Customer’s own use and not for resale.
LIBERTY GARDEN PRODUCTS LIMITED WARRANTY CONTINUED 2.
