Installation Instructions For Wine Cooler HWgb(w) 3300, HWgb(w) 5100, HWgb(w) 8300 7085 015-00
Table of Contents Please Read and Follow These Instructions These instructions contain Danger, Warning and Caution notes. This information is important for safe and efficient installation and operation. Always read and comply with all Danger, Warning and Caution notes! DANGER! Danger indicates a hazard which will cause serious injury or death if precautions are not followed. WARNING! Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Safety Blocking for Safety WARNING! To avoid a hazard due to instability of the appliance, it must be fixed in accordance with the instructions. Disposal of Old Appliance DANGER! Risk of child entrapment. Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for “just a few days.
Unpacking Supplied Accessories Stabilizing rail handle Labels 2 pcs. - HW 3300 4 pcs. - HW 5100 8 pcs. - HW 8300 Attachment bracket Cover Spacer Cover Spacer Cover profile Cover profile Attachment bracket Open-ended wrench Stabilizing rail 2 pcs.
Transporting the appliance WARNING! An appliance which has not been built in can topple over! 2 pcs. 2 pcs. 5 pcs. 2 pcs. Transporting the Appliance CAUTION! Danger of injury or damage as a result of incorrect transport! - Transport the appliance in a packed condition. - Transport the appliance upright. - Do not transport the appliance without assistance.
Planning Information Appliance Venting HWgb(w) 3300 Appliance Dimensions Dimensions of Appliance Door IMPORTANT The clear ventilation cross-section must be at least 31 sq inches from the bottom to the top opening. Types of Air Outlet 1 Directly above the appliance 2 Above the top cabinet 3 From the front of the top cabinet with decor grille IMPORTANT When using decor grilles, the sum of the individual openings must total a minimum of 31 square inches.
Planning Information Installation Dimensions Top View IMPORTANT In order to avoid any problems when installing the appliance and to avoid damage to the appliance: The floor on which the appliance stands must be horizontal and level. The kitchen cabinets must be aligned horizontally and vertically. Cabinet Dimensions Maximum door opening angle The power cord exits the rear of the appliance at this location.
Planning Information HWgb(w) 5100 Appliance Dimensions Top View Dimensions of Appliance Door Maximum door opening angle Side View 8
Planning Information Installation Dimensions IMPORTANT In order to avoid any problems when installing the appliance and to avoid damage to the appliance: The floor on which the appliance stands must be horizontal and level. The kitchen cabinets must be aligned horizontally and vertically. Cabinet Dimensions The power cord exits the rear of the appliance at this location.
Planning Information HWgb(w) 8300 Appliance Dimensions Dimensions of Appliance Door Top View Maximum door opening angle 10 Side View
Planning Information Installation Dimensions IMPORTANT In order to avoid any problems when installing the appliance and to avoid damage to the appliance: The floor on which the appliance stands must be horizontal and level. The kitchen cabinets must be aligned horizontally and vertically. Cabinet Dimensions The power cord exits the rear of the appliance at this location.
Installation Installing the Appliance The installation work should only be carried out by trained personnel. Two people are required for the installation work. Note Check the installation dimensions before installation. The intermediate panel and side wall of the kitchen cabinet must be perpendicular to each other. WARNING! Fire hazard due to dampness! If live parts or the power cord become damp this may cause short circuits. - The appliance is designed for use in enclosed areas.
Installation 7. Only if the wall thickness is less than 3/4" (19 mm): Fit the spacers. 5. Fit cover profile. 5/8" (16 mm) On appliances with hinges on the left 5. On appliances with hinges on the right 7. 3/4" (19 mm) 6. Remove the transportation safety component. 8. Remove cover. 6. 8.
Installation 9. Screw on the attachment bracket. 9. 12. Fit cover profile. 12. 13. Slide the appliance fully into the recess. Check that the distance is identical all the way round. 10. 10. Screw on the attachment bracket. • Undo the screws 1. • Slide bracket towards the cabinet wall. • Tighten the screws 1. 11. Remove edge protection. 13. 11.
Installation 14. Adjust appliance using the adjustable feet, see section entitled “Adjusting the door”, page 17. 16. Snap off and remove the front part of the stop bracket. 14. 16. 15. Secure the appliance to the kitchen cabinet using screws through the hinges and attachment brackets. 17. Fit the covers. 15. 17.
Installation 18. Stabilize the appliance at the back at the bottom: 20. Remove cover. Fit the handle 1 to the stabilizing rail 2 and slide the stabilizing rail into the floor of the appliance. Remove the handle and repeat this procedure with the second stabilizing rail. 20. 21. Remove the transportation safety component. 18. 21. 22. Screw on the cover. 22. 19. Remove seal. 19. 23. Fit cover. 23.
Installation 24. Fit seal. 2. Remove covers. 24. 2. Check that the appliance is secure in the kitchen cabinet and that the door closes properly. 3. • Remove screws 1. Installation is now complete. • Transfer to position 2. • Undo screws 3. • Adjust clearance. • Tighten screws 1 and 3. Adjusting the Door 3. 1. Remove seal. 1.
Changing Over Door Hinges Changing Over Door Hinges 4. Fit the covers. Door hinges should only be changed by a trained expert. Changing the door hinges must be done by two people. WARNING! 4. High door weight. Danger of injury and damage to property. Only complete the modification work if you can lift a weight of 132 lbs (60 kg). WARNING! Risk of injury due to the door dropping out! If the fastening parts are not screwed into place firmly enough, the door may drop out.
Changing Over Door Hinges 2. Remove covers. 3. Remove seal. 3. 2. 4. Remove cover. 4. 5. Remove cover. 5.
Changing Over Door Hinges 6. Remove seal. 9. Remove the door. The door must now be held secure by somebody. Carefully place the door on a soft surface. 9. 6. CAUTION! Risk of injury if hinges fold! - Leave hinges open. 7. Remove cover. 10. 7. 10. Remove the upper retaining bracket and transfer to the opposite side. 8. Remove the transportation safety component. 11. 11. Transfer the stop to the opposite side. 8.
Changing Over Door Hinges 12. Remove seal. 15. Re-fit the hinges on the opposite side at diagonals to the original position (see section entitled “Adjusting the door”, page 17). 12. 13. Remove covers. 13. 15. 14. Unscrew hinges. 14.
Changing Over Door Hinges 19. Fit the covers. 19. 16. Screw on covers. 16. 20. 20. Fit seal. 17. 17. Fit the covers. 21. Fit the door on the appliance. Notice The door must now be held secure by somebody. 18. Fit seal. 22 18. 21.
Changing Over Door Hinges 22. Fit covers and click into place. 22. Check that the door is securely fitted to the appliance and closes properly.
For Service in the U.S. Liebherr Service Center Toll Free: 1-866-LIEBHER or 1-866-543-2437 Email: Service-appliances.us@liebherr.com PlusOne Solutions, Inc. 3501 Quadrangle Blvd, Suite 120 Orlando, FL 32817 For Service in Canada Liebherr Service Center Toll Free: 1-888-LIEBHER or 1-888-543-2437 www.euro-parts.ca EURO-PARTS CANADA 39822 Belgrave Road Belgrave, Ontario, N0G 1E0 Phone: (519) 357-3320 Fax: (519) 357-1326 *708501500* w w w. l i e b h e r r - a p p l i a n c e s .
