Installation Instructions For Wine Cooler and Beverage Center WU 3400 / WU 4500 / RU 510 7080 192-02
Table of Contents Please Read and Follow these Instructions These instructions contain Danger, Warning and Caution notes. This information is important for safe and efficient installation and operation. Always read and comply with all Danger, Warning and Caution notes! DANGER! Danger indicates a hazard which will cause serious injury or death if precautions are not followed. Contents Page Disposal of Old Appliance............................................. 3 Important Safety Information............
Safety Disposal of Old Appliance DANGER! Risk of child entrapment. Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents. Before you discard old appliances: • Take off the doors. • Leave the shelves in place so that children may not easily climb inside.
Unpacking Supplied Accessories 2 pcs. Magnet bracket Cover strips 2 pcs. Toe kick panel Angle bracket (For mounting a cover plate on the top or bottom of the appliance) Dust filter 4 pcs. 4 pcs. 4 pcs. Screws for toe kick panel assembly Foam block for ventilation duct in appliance base 4 x 20 3.7 x 17 4 x 35 Wrench to adjust the height of the appliance 2 pcs. Base bracket Retaining screws for installation 3 pcs. 4 x 14 4 2 pcs. 4 x 19 3 pcs.
Planning Information Air Flow in the Appliance Base 2 pcs. Adjustable feet support IMPORTANT To ensure proper refrigeration performance of the appliance, the toe kick panel supplied must be installed. 2 pcs. The foam block supplied must be installed in order to ensure the required air flow through the appliance base. Dimensions of Appliance Door 28-1/8" 1/16" (714 mnm) Toe kick panel Failure to follow this instruction may result in poor refrigeration performance.
Planning Information Appliance Dimensions Installation Dimensions IMPORTANT Side view In order to avoid any problems when installing the appliance and to avoid damage to the appliance: The floor on which the appliance stands must be horizontal and level. 32-1/8" (816 mm) The kitchen units must be aligned horizontally and vertically. 3" (76 mm) 4" (102 mm) 3-15/16" (100 mm) Height when adjustable feet have been screwed in as far as they will go.
Planning Information Angle Bracket for Cover Panel Depending on the height of the toe kick and the height of the counter, the supplied angle bracket can be installed on the top or bottom of the appliance to cover unwanted openings with a panel. The long holes in the bracket enable the bracket to slide in and out in order to align the filler panel with the front of the door.
Planning Information Mounting the Dust Filter The supplied dust filter prevents dirt from getting into the motor compartment, which can impair the refrigeration performance. Therefore, always install the dust filter. Mounting the premounted bracket on the appliance bottom • Use two 4 x 19 screws. Remove the protective film from the dust filter. Insert the filter at the bottom and click into place at the top. • Screw into the designated holes. Do not tighten the screws yet.
Installation Installing the Appliance 1. Open the door and remove the top left cover. 2. Apply the cover strips to the leading edge of the appliance housing on the left and right. 1. The bottom of the strip must be in line with the bottom edge of the appliance housing (see detail below). 2. Installing version without cover panel on the appliance top Adjust the height of the appliance leaving a gap of approx. 1/8" between the appliance top and the underside of the countertop.
Installation 5. Fit the adjustable feet support. 7. 4 x 29 TX™ 15 7. • Screw the appliance to the body of the unit at the top left-hand side. 5. • Click cover (1) into place again. 8. Screw the appliance to the body of the unit at the bottom on the left and right. 6. Slide in the appliance until the front surface of the appliance door is flush with the unit fronts. 8. 6.
Installation 9. Use screw A or B, depending on the position of the base of the adjacent cabinet. Fit the magnet brackets to the screw heads. 11. Cut the foam block to the correct height – the depth will depend on the position of the base of the adjacent cabinet. 11. 9. IMPORTANT If the foam block is not installed, the appliance will not deliver optimal refrigeration performance during operation. 12. Fit the toe kick panel. 1/16" (1.4 mm) 12. 1/16" (1.4 mm) 10.
Changing Over Door Hinges Changing Over Door Hinges Door hinges should only be changed by a trained expert. Changing over the door hinges requires two people. Note The following description depicts appliance WU 3400. The same procedure applies to changing the door hinges on the WU 4500 and RU 510 appliances. 3. Important The door must now be held secure by another person. 1. Remove screw. 3. Pull out hinge pin. 1. 4. Remove upper hinge pin. 4. 2. Remove screw. 2.
Changing Over Door Hinges 5. Move the door towards the appliance until the pin in the hinge bracket is visible (see detailed drawing). Remove door. 8. 5. 8. Compress the covers in the places shown and release. Turn the covers 180° and click into place on the opposite side. 6. Remove cover. 7. Unscrew door latch. 6. 7. 9. Click cover into place. 9. 10. Screw on the door latch. 10.
Changing Over Door Hinges 11. Transfer door handle and plugs to the opposite side. 13. 11. 13. Unscrew upper hinge bracket. This will subsequently be refitted on the left at the bottom. 14. Unscrew the lower hinge bracket. This will subsequently be refitted on the left at the top. 12. Remove the covers. 12. 14 14.
Changing Over Door Hinges 15. 15. Remove the upper retaining bracket and transfer to the opposite side. 17. 17. Screw in the hinge bracket (from bottom right) at the top left. 16. 16. Remove the lower retaining bracket and transfer to the opposite side. 18. 18. Screw in the hinge bracket (from top right) at the bottom left.
Changing Over Door Hinges 19. 21. 19. Fit the door on the hinge brackets. Important The door must now be held secure by another person. 21. Insert the bottom hinge pin in the same way. 20. 20. Insert hinge pin. The door must be open 90°. Insert the hinge pin with the flat part facing the appliance. 22. Screw in the screws at the top and bottom. The hinge pin must be fully inserted in the borehole and may not protrude at the top. 22.
Changing Over Door Hinges 23. 23. Close door and check to ensure that it is aligned with the side walls of the appliance. 25. Adjusting the lateral tilt of the door If the door is at an angle, adjust the angle. 25. Fit the covers. 24. Undo screws and slide hinge bracket to the right or left. Tighten screws. 24.
For Service in the U.S. Liebherr Service Center Toll Free: 1-866-LIEBHER or 1-866-543-2437 Email: Service-appliances.us@liebherr.com PlusOne Solutions, Inc. 3501 Quadrangle Blvd, Suite 120 Orlando, FL 32817 For Service in Canada Liebherr Service Center Toll Free: 1-888-LIEBHER or 1-888-543-2437 www.euro-parts.ca EURO-PARTS CANADA 39822 Belgrave Road Belgrave, Ontario, N0G 1E0 Phone: (519) 357-3320 Fax: (519) 357-1326 *708019202* w w w. l i e b h e r r - a p p l i a n c e s .
