Phau Ntawv Qhia

DIGITAL TRANSMITTER MODEL 3089

Congratulations! You have just purchased a MULTI-CODE Digital Transmitter,

which we believe to be the fi nest product of its kind on the market. With a little

care this transmitter should provide you with many years of excellent service.

Please take a moment to read the following instructions and you will fi nd that setting

your new transmitter will be quite an easy matter.

ACCESSING THE CODE SWITCH

Insert a small coin into the slot located at the bottom end of the transmitter. Twist

the coin and remove the access cover to expose the code switch and battery

compartment.

10029379 Rev A

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,MC3089 ,1 CH,TX -

P/N: 10029379 Rev A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 9.000” X 3.500” - SCALE: 1-1 - SIDE 1 OF 2

INSTALLATION INSTRUCTIONS

USA & Canada (800) 421-1587 & (800) 392-0123

(760) 438-7000 - Toll Free FAX (800) 468-1340

www.nortekcontrol.com

WARNING: Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the

equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC & IC Notice

This device complies with Part 15 of the FCC Rules and Industry Canada license exempt standard(s). Operation is subject to

the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference received that may cause undesired operation.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation

est autorisée aux deux conditions suivantes:

1) l’appareil ne doit pas produire de brouillage, et

2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

PAGE 1
PRINTER’S INSTRUCTIONS: INSTR,INSTL,MC3089 ,1 CH,TX - P/N: 10029379 Rev A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 9.000” X 3.500” - SCALE: 1-1 - SIDE 1 OF 2 WARNING: Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the Federal Communications Commission (FCC) rules.
PAGE 2
PRINTER’S INSTRUCTIONS: INSTR,INSTL,MC3089 ,1 CH,TX - P/N: 10029379 Rev A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 9.000” X 3.500” - SCALE: 1-1 - SIDE 2 OF 2 8 9 10 SELECTING A CODE You may set your transmitter to any code you desire but be sure that the code you set matches the code that has been set on your radio receiver. The digital code is determined by the positions of the 10 small switches numbered 1 through 10 located in the receiver and transmitter.