SDS

ManualsBrandsLiquid Wrench ManualsAutomotivePenetrating Oil -11 oz.

SAFETY DATA SHEET

1. Identification

Liquid Wrench Penetrating OilProduct identifier

Other means of identification

L112

SDS number

L106, L112

Part No.

3403.19.5000

Tariff code

Penetrating Oil

Recommended use

None known.

Recommended restrictions

Manufacturer/Importer/Supplier/Distributor information

Manufacturer

RSC Chemical Solutions

Address

600 Radiator Road

Company name

Website

Telephone

Customer Service: (704) 821-7643

Technical: (704) 684-1811

Emergency phone number

Emergency Telephone: (303) 623-5716

Emergency Contact: RMPDC (877-740-5015)

E-mail

United States

www.rscbrands.com

sds@rscbrands.com

Indian Trail, NC 28079

2. Hazard(s) identification

Category 2Flammable aerosols

Physical hazards

Category 2Skin corrosion/irritation

Health hazards

Category 3 narcotic effectsSpecific target organ toxicity, single exposure

Category 2Specific target organ toxicity, repeated

exposure

Category 1Aspiration hazard

Not classified.

Environmental hazards

Not classified.

OSHA defined hazards

Label elements

Signal word

Danger

Hazard statement

Flammable aerosol. Contains gas under pressure; may explode if heated. May be fatal if

swallowed and enters airways. Causes skin irritation. May cause drowsiness or dizziness. May

cause damage to organs through prolonged or repeated exposure.

Precautionary statement

Prevention

Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an open

flame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Do

not breathe mist or vapor. Wash thoroughly after handling. Use only outdoors or in a

well-ventilated area. Wear protective gloves.

Response

If swallowed: Immediately call a poison center/doctor. If on skin: Wash with plenty of water. If

inhaled: Remove person to fresh air and keep comfortable for breathing. Call a poison

center/doctor if you feel unwell. Do NOT induce vomiting. If skin irritation occurs: Get medical

advice/attention. Take off contaminated clothing and wash before reuse.

Storage

Store in a well-ventilated place. Keep container tightly closed. Store locked up. Protect from

sunlight. Do not expose to temperatures exceeding 50°C/122°F.

1 / 8

Material name: Liquid Wrench Penetrating Oil

L106, L112 Version #: 04 Revision date: 02-08-2016 Issue date: 04-27-2015

SDS US

Summary of content (8 pages)

PAGE 1
SAFETY DATA SHEET 1. Identification Product identifier Liquid Wrench Penetrating Oil Other means of identification SDS number L112 Part No. L106, L112 Tariff code 3403.19.5000 Recommended use Penetrating Oil Recommended restrictions None known. Manufacturer/Importer/Supplier/Distributor information Manufacturer Company name Address Telephone Website E-mail Emergency phone number RSC Chemical Solutions 600 Radiator Road Indian Trail, NC 28079 United States Customer Service: Technical: www.
PAGE 2
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations. Hazard(s) not otherwise classified (HNOC) None known. Supplemental information None. 3. Composition/information on ingredients Mixtures Chemical name Common name and synonyms CAS number % Carbon Dioxide 124-38-9 1-<3 Fresh Fragrance Trade Secret < 0.
PAGE 3
Methods and materials for containment and cleaning up Environmental precautions Refer to attached safety data sheets and/or instructions for use. Keep combustibles (wood, paper, oil, etc.) away from spilled material. Stop leak if you can do so without risk. Move the cylinder to a safe and open area if the leak is irreparable. Cover with plastic sheet to prevent spreading. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.
PAGE 4
General hygiene considerations When using do not smoke. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. 9. Physical and chemical properties Appearance Liquid. Opaque Physical state Liquid. Form Aerosol. Color Yellow Odor Fragrance Odor threshold Not available. pH Not available. Melting point/freezing point Not available.
PAGE 5
Conditions to avoid Avoid temperatures exceeding the flash point. Contact with incompatible materials. Incompatible materials Strong oxidizing agents. Hazardous decomposition products No hazardous decomposition products are known. 11. Toxicological information Information on likely routes of exposure May cause damage to organs through prolonged or repeated exposure by inhalation. May cause Inhalation drowsiness and dizziness. Headache. Nausea, vomiting. Skin contact Causes skin irritation.
PAGE 6
Waste from residues / unused products Contaminated packaging Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions). Since emptied containers may retain product residue, follow label warnings even after container is emptied. Empty containers should be taken to an approved waste handling site for recycling or disposal. Do not re-use empty containers. 14.
PAGE 7
15. Regulatory information US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D) Not regulated. CERCLA Hazardous Substance List (40 CFR 302.4) Not listed. SARA 304 Emergency release notification Not regulated. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) Not listed.
PAGE 8
Country(s) or region New Zealand Inventory name New Zealand Inventory On inventory (yes/no)* Yes Philippines Philippine Inventory of Chemicals and Chemical Substances (PICCS) Yes United States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory Yes *A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s) A "No" indicates that one or more components of the product are not listed or exempt from listing on the invent