Installation Guide

ManualsBrandsLitex ManualsCeiling FansSCH52BB5L

net fan weight: 16.53 lb. (7.5 kg)

Table of Contents:

Safety Tips. pg. 1

Unpacking Your Fan. pg. 2

Parts Inventory. pg. 2

Installation Preparation. pg. 3

Hanging Bracket Installation. pg. 3

Preparation for Wiring. pg. 4

Wiring. pg. 5

Fan Assembly. pg. 5

Motor Housing Assembly. pg. 6

Blade Assembly. pg. 6

Light Kit Assembly (optional). pg. 7

Testing Your Fan. pg. 7

Troubleshooting. pg. 8

Warranty. pg. 8

Parts Replacement. pg. 8

Installation Guide

For Model:

C-SCH52BNK5L

READ THESE INSTRUCTIONS AND

SAVE THEM FOR FUTURE USE

PRINTED IN CHINA

4009654

Summary of content (9 pages)

PAGE 1
READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For Model: C-SCH52BNK5L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Preparation for Wiring. pg. 4 Wiring. pg. 5 Fan Assembly. pg. 5 Motor Housing Assembly. pg. 6 Blade Assembly. pg. 6 Light Kit Assembly (optional). pg. 7 Testing Your Fan. pg. 7 Troubleshooting. pg. 8 Warranty. pg. 8 Parts Replacement. pg.
PAGE 2
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
PAGE 3
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. a 2. Parts Inventory. a. hanging bracket. 1 piece b b. motor housing*. 1 piece c c. motor assembly. 1 piece d. switch housing cap. 1 piece d e. blade arm.* 5 pieces f.
PAGE 4
3. Installation Preparation. To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 12ft. - 20ft. (3.66m - 6.1m) blade edge 30 inches 7 feet (76cm) (2.13m) 12ft. - 20ft. (3.66m - 6.
PAGE 5
. Preparation for Wiring. Remove 4 motor mounting screws and lock washers from the bar on the top of motor assembly; leave rubber cushions in place. Lift motor assembly to hanging bracket and place one end of motor assembly in hanging bracket slot. This will allow motor assembly to hang out of the way while wiring. Tip: Seek the help of another person to hold the stepladder in place and to lift the fan up to you once you are set on the ladder.
PAGE 6
. Wiring. CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. GROUND (GREEN OR BARE) GREEN Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code. If you are unfamiliar with electrical wiring or if the house/building wires are different colors than those referred to in the instructions below, please use a qualified electrician.
PAGE 7
8. Motor Housing Assembly. Temporarily hold motor housing up to hanging bracket to determine which 2 screws align with slotted holes on top rim of motor housing. Put motor housing down and partially loosen the 2 screws in the hanging bracket that correspond to slotted holes in motor housing. Remove the other 2 screws, along with star washers, from the hanging bracket.
PAGE 8
10. Light Kit Assembly (Optional). reverse switch motor housing If you wish to use your fan WITH the light kit, Remove 3 screws from light kit fitter. Locate BLUE (or BLACK) and WHITE wires in the switch housing labeled FOR LIGHT KIT CONNECTION. Remove and discard plastic that holds these 2 wires together. switch housing Connect WHITE wire from switch housing to WHITE wire from light kit fitter. Connect BLUE (or BLACK) wire from switch housing to BLACK wire from light kit fitter.
PAGE 9
Troubleshooting. Warranty. Problem: Fan fails to operate. Solutions: 1. Check wall switch to fan. 2. Verify that reverse switch is set completely in either direction. 3. Check to be sure fan is wired properly. Problem: Light kit (optional) not lighting. Solutions: 1. Check wall switch to fan. 2. Check that bulbs are installed correctly. 3. Check to be sure wires in outlet box are wired properly. 4. Verify that molex connections in switch housing are connected properly.