READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For Models: UB48BC4L UB48WW4L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pg. 4 Wiring. pg. 5 Canopy Assembly. pg. 6 Blade Assembly. pg. 6 Light Kit Assembly. pg. 7 Testing Your Fan. pg. 7 Troubleshooting. pg. 8 Parts Replacement. pg. 8 Warranty. pg. 8 4009654 net weight of fan: 13.66 lb (6.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a a. hanging bracket. 1 piece b. blade. 4 pieces b c. motor housing, downrod and canopy (pre-assembled). 1 piece c d. glass shade. 1 piece e.
3. Installation Preparation. blade edge 12ft. - 15ft. (3.66m - 4.57m) To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 10ft. (3.05m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 225 square feet (20.9 square meters). 30 inches 10 feet (76cm) (3.05m) 12ft. - 15ft. (3.66m - 4.57m) This fan can be mounted with a downrod on a normal ceiling only.
. Fan Assembly. With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Loosen canopy set screw and lower canopy to expose hanging ball at top of downrod. Remove plastic from end of safety cable. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on hanging bracket. Turn hanging ball until slot lines up with hanging bracket tab.
. Wiring. WARNING: Turn off circuit breakers to current fixture from breaker panel and be sure switch is turned to the OFF position. CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. white supply wire black supply wire from ceiling black white Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.
. Canopy Assembly. Raise canopy to hanging bracket until canopy touches the ceiling. Tighten the canopy set screw to secure canopy. Carefully remove protective paper from downrod. canopy canopy set screw downrod 8. Blade Assembly. Remove protective film from both sides of blade. Locate one of the rubber cushions on top of motor housing. Remove the 2 larger screws (do not remove center screw) and washers but leave rubber cushion intact.
9. Light Kit Assembly. Install one 6.5 watt medium base LED bulb (included). IMPORTANT: When replacing bulb, please allow bulb and glass shade to cool before touching. reverse switch Partially loosen 3 thumbscrews at bottom of motor housing and raise glass shade to motor housing. Secure glass shade with thumbscrews. Be sure thumbscrews make contact with rubber ring on glass shade, but do NOT overtighten thumbscrews as glass may crack or break. motor housing thumbscrew bulb 10. Testing Your Fan.
Troubleshooting. Warranty. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. LITEX 15-YEAR LIMITED WARRANTY: LITEX INDUSTRIES, LTD. warrants this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or repair any fan which has faulty performance due to a defect in material or workmanship.
LEER ESTAS INSTRUCCIONES Y GUARDARLAS PARA UTILIZACIÓN FUTURA Guía de instalación Para modelos: UB48BC4L UB48WW4L Índice de materias: Sugerencias de seguridad. Pág. 1 Desempaquetado del ventilador. Pág. 2 Inventario de piezas. Pág. 2 Preparación para la instalación. Pág. 3 Instalación del soporte de montaje. Pág. 3 Ensamblaje del ventilador. Pág. 4 Instalación eléctrica. Pág. 5 Colocación de la cubierta decorativa. Pág. 6 Colocación de las aspas. Pág. 6 Instalación del juego de luz. Pág.
SUGERENCIAS DE SEGURIDAD. ADVERTENCIA: Para evitar la posibilidad de una descarga eléctrica, desconectar la corriente en la caja de fusibles principal o el interruptor protector antes de iniciar la instalación del ventilador o antes de repararlo o instalar accesorios. 1. LEER TODAS LAS INSTRUCCIONES E INFORMACIÓN DE SEGURIDAD CUIDADOSAMENTE ANTES DE INSTALAR SU VENTILADOR Y GUARDAR ESTAS INSTRUCCIONES.
1. Desempaquetado del ventilador. Abrir el empaque cuidadosamente. Sacar los artículos del embalaje. Sacar el motor y ponerlo en una alfombra o en el embalaje para evitar rayar el acabado. Guardar la caja de cartón o el empaquetamiento original en caso de que tenga que mandar el ventilador para alguna reparación. Comprobar las piezas del ventilador con el inventario de piezas y verificar que se incluyen todas. 2. Inventario de piezas. a a. soporte de montaje. 1 unidad b. aspa. 4 unidades b c.
Para prevenir daño corporal y otros daños, estar seguro de que el lugar en donde va a colgar el ventilador le permite un espacio libre de 3,05m (10 pies) entre las puntas de las aspas y el piso y 76cm (30 pulg.) entre las aspas y cualquier pared u otra obstrucción. Este ventilador es adecuado para habitaciones hasta 20,9 metros cuadrados (225 pies cuadrados). 3,66m - 4,57m (12 pies - 15 pies) 3. Preparación para la instalación.
5. Ensamblaje del ventilador. Ya que esté sujetado el soporte de montaje a la caja de salida y capaz de apoyar el ventilador, usted está listo para colgar el ventilador. Aflojar el tornillo de fijación de la cubierta decorativa y bajar la cubierta decorativa para poner a la vista la bola que sirve para colgar en la parte superior del tubo. Quitar el plástico del extremo del cable de seguridad. Agarrar el ventilador firmemente con las dos manos.
6. Instalación eléctrica. ADVERTENCIA: Apagar los cortacircuitos en el panel de electricidad que suplen corriente a la caja de salida y asegurarse de que el interruptor de luz esté APAGADO. PRECAUCIÓN: Asegurarse de que la caja de salida esté conectada a tierra como es debido y que exista un conductor a tierra (VERDE o pelado).
7. Colocación de la cubierta decorativa. Subir la cubierta decorativa hasta que esté pegada al techo. Apretar el tornillo de fijación de la cubierta decorativa para asegurar la cubierta decorativa. cubierta decorativa tornillo de fijación de la cubierta decorativa Con cuidado quitar el papel protector del tubo. tubo 8. Colocación de las aspas. Quitar la película protectora de ambos lados de un aspa. Localizar una de las arandelas de protección de hule en la parte superior del bastidor del motor.
9. Instalación del juego de luz. Instalar 1 bombilla LED de base mediana de 6,5 vatios (incluida). IMPORTANTE: Cuando necesite reemplazar la bombilla, favor de dejar que se enfríen la bombilla y la pantalla de vidrio antes de tocarlas. Aflojar parcialmente los 3 tornillos de mariposa en la parte inferior del bastidor del motor y subir la pantalla de vidrio hasta el bastidor del motor. Asegurar la pantalla de vidrio con los tornillos de mariposa.
Localización de fallas. Garantía. ADVERTENCIA: El no desconectar el suministro de GARANTÍA LIMITADA DE 15 AÑOS DE LITEX: LITEX INDUSTRIES, LTD. garantiza este ventilador al comprador original de grupo familiar para uso interior con las siguientes condiciones: GARANTÍA DE 1 AÑO: LITEX INDUSTRIES, LTD. reemplazará o reparará cualquier ventilador que tenga funcionamiento deficiente debido a defectos en los materiales o trabajo manual.