Specification

LED Recessed Downlighting
4BE
4” LED Module
IC/Non-IC
Retrofit
FEATURES & SPECIFICATIONS
INTENDED USE — Our recessed LED module is the most economical means to create a well lit environ-
ment with exceptional energy efficiency and near zero maintenance. Great for retrofit into existing
downlight cans or new construction and remodel applications. Compliant friction clip retention allows
fitment into nearly 100% of installed cans. The LED module maintains at least 70% light output for 35,000
hours. Indoor and Outdoor Use.
CONSTRUCTION — Aluminum spun reflector with deep baffle configuration for reduced glare.
Combined LED and driver printed circuit board attached. Inner reflector cone funnels light through the
pressed-in diffused lens.
OPTICS — Diffused lens at end of mixing chamber to provide even light distribution for general illumina-
tion, equivalent to 65W BR30 Lamp.
Wide flood beam angle at > 45°.
ELECTRICAL — Center 2 Edge™ (patent pending) technology created for a single point source. Primary
power disconnect provided for simple connection to a dedicated LED connector in the housing.
Dimming down to 10%. For compatible dimmers, refer to Compatible Dimmers Chart.
700-lumen E series has an input wattage of 10 watts, 70 lumens per watt, equivalent to 65-watt
incandescent.
E Series' patent pending driver has zero inrush which allows power loads to be calculated with actual
rated wattages.
Example: 60 units of 4BEMW LED fixtures can be installed in line with a 600-watt dimmer. 600W/10W
= 60 fixtures.
INSTALLATION — Suitable for installation in standard height rough-in sections.
E26 socket adapter and ships standard.
Friction clips allow fitment into cans with an inside diameter of 4.0” to 4.5".
LISTINGS — CSA certified to US and Canadian safety standards. ENERGY STAR® certified. Can be used to
comply with California Title 24 Part6 High Efficacy LED Light Source Requirements. Wet location listed.
WSEC ASTM E283 for Air-Tight (with IC housings).
WARRANTY — 5-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
NOTE: Actual performance may differ as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25°C.
Specifications subject to change without notice.
PATENTS PENDING.
Notes
1 Total system delivered lumens.
2 Must be ordered on a separate line.
DOWNLIGHTING 4BE T24 LED
E26 adaptor
(included)
ORDERING INFORMATION
All configurations of this product are considered "standard" and have short lead times.
Example: 4BEMW LED 27K 90CRI L3LED T24
LED
Series/Finish Lamp CCT / W / Lumens
1
CRI Voltage Housing Options
4BEMW 4" Baffle LED module, matte white LED 27K 2700K / 9.8W / 650L
30K 3000K / 9.8W / 700L
35K 3500K / 10W / 700L
40K 4000K / 9.8W / 720L
50K 5000K / 9.8W / 700L
90CRI 90CRI (blank) 120V L3LED T24 4" new construction rough-in LED base
L3RLED T24 4" remodel rough-in LED base
L3 4" new construction rough-in
2
L3R 4" remodel rough-in
2
Specifications
Aperture: 4-1/8 (10.5)
Ceiling opening: Determined by rough-in
Overlap trim: 5-1/4 (13.3)
Height: 2-1/2 (6.3)
All dimensions are inches (centimeters) unless otherwise indicated.
4-1/8
(10.5)
2-1/
2
(6.3)
5-1/4
(13.3)
Catalog
Number
Notes
Type
D
I
M
M
A
B
L
E