Technical Specifications
®
SPECIFICATIONS
ORDERING INFO
OPTIONS
OCCUPANCY CONTROLLED
DIMMING (D)
• Provides dimming output to control
0-10 VDC dimmable ballasts
• Provides a second occupancy time-
out period that enables the lights to go
to a dim setting before turning off
• Adjustable max/min dim setting
PHOTOCELL (P)
• Auto set-point calibration
• Two selectable modes of operation
• On/Off mode: Photocell has full
control during periods of occupancy
• Inhibit mode: Photocell can prevent
lights from turning on if adequate
daylight is available, but can not turn
lights off
PHOTOCELL W/ DIMMING (ADC)
• Photocell within sensor maintains total
room light level by controlling levels of
0-10 VDC dimmable ballasts
• Photocell also has full on/off control
during periods of occupancy
• Provides a second occupancy time-
out period that enables the lights to go
to a dim setting before turning off
Note: LampMaximizer+ features not
available with ADC option
347 VAC (347)
• Allows sensor to be powered from
and switch 347 VAC
LOW TEMP/HIGH HUMIDITY (LT)
• Sensor is corrosion resistant to
moisture
• Operates down to -4º F (-20ºC)
OVERVIEW
The CMRB PDT 10 Series occupancy sensor
mounts directly to the end of a pendant or
surface mounted xture and provides patented
PIR/Microphonics™ (PDT) detection over a
range of 50 ft (15.24 m). When mounted at 9
ft (2.74 m) this sensor provides line of sight PIR
detection up to 28 ft (8.53 m) in all directions
and combines overlapping Microphonics™
for detection around obstructions. The CMRB
PDT 10 is ideal for large storage rooms or
classrooms where surface mounting a sensor
is not practical. The CMRB PDT 10 is line
powered and can switch loads directly without
the need for a power pack.
SENSOR OPERATION
Sensors with Passive Dual Technology
(PDT) rst see motion using 100% digital
Passive Infrared (PIR) detection and then
engage Microphonics™ to hear sounds that
indicate continued occupancy. This patented
technology uses Automatic Gain Control
(AGC) to dynamically self adapt a sensor
to its environment by ltering out constant
background noise and registering only noises
typical of human activity. When occupancy is
detected, a self-contained relay switches the
lighting on. If needed, a 10 second grace period
also allows the lights to be voice reactivated
after shutting off. This sensor is line powered,
switches line voltage, and requires no eld
calibration or sensitivity adjustments.
LAMPMAXIMIZER
®
This sensor also contains patent pending
LampMaximizer technology that allows users
to aggressively target energy savings while still
protecting lamp life. A minimum on timer, factory
set at 15 minutes, helps preserve lamp life by
eliminating all lamp cycles shorter than lamp
warranties specify.
A standard occupancy time delay is also present
that ensures lights turn off (assuming minimum
on timer has elapsed) if no occupancy is
detected. This timer is factory set at 10 minutes
to promote energy savings, but is adjustable
between 30 seconds and 20 minutes. These
adjustments can be done manually, through
the unit’s push-button, or automatically every
two weeks through an advanced mode, called
LampMaximizer+, that determines the optimum
time delay in order to maximize both lamp life
and energy savings. Additionally, this sensor
maintains statistics on total lamp on time and
number of cycles.
EXTENDED RANGE 360º SENSOR
FIXTURE MOUNT BOX • LINE VOLTAGE • DUAL TECHNOLOGY (PDT)
CMRB PDT 10
FEATURES
100% Digital PIR Detection,
Excellent RF Immunity
360º Coverage Pattern
Patented Dual Technology with
PIR / Microphonics Detection
Self-Contained Relay,
No Power Pack Needed
No Minimum Load Requirements
Interchangeable Hot & Load Wires,
Impossible to Wire Backwards
Push-Button Programmable
Adjustable Time Delays
No Field Calibration or Sensitivity
Adjustments Required
Convenient Test Mode
100 hr Lamp Burn-in Timer
Green LED Indicator
LAMPMAXIMIZER
®
TECHNOLOGY
• Protects Lamp Life while
Maximizing Energy Savings
• Minimum On Timer (15 min default)
• Occ. Time Delay (10 min defatult)
• LampMaximizer+ Mode -
Optimizes Lamp Life & Energy
Savings (disabled by default)
• Switch Counter (in 1000’s)
• Total Lamp On Time (in khrs)
PHYSICAL / MATERIAL SPECS
SIZE 3.63” H x 3.63” W x 1.50” D
(9.22 cm x 9.22 cm x 3.81 cm)
WEIGHT 6 oz
MOUNTING 1/2” knockout
COLOR White
OPERATING TEMP
14º to 160º F (-10º to 71º C)
STORAGE TEMP
-14º to 160º F (-26º to 71º C)
RELATIVE HUMIDITY
20 to 90% non-condensing
SILICONE FREE
ROHS COMPLIANT
ELECTRICAL SPECS
MAXIMUM LOAD
800 W @ 120 VAC
1200 W @ 277 VAC
1500 W @ 347 VAC
MINIMUM LOAD None
MOTOR LOAD 1/4 HP
FREQUENCY 50/60 Hz
DIMMING LOAD Sinks < 20mA;
~40 Ballasts @ .5mA each
VOLTAGE
TEMP/HUMIDITY
Blank = None Blank = 120/277 VAC Blank = Standard
D = Occupancy Controlled Dimming 347 = 347 VAC LT = Low Temp
P = Photocell
ADC = Photocell w/ Dimming
CMRB PDT 10 [DIMMING/PHOTOCELL] [VOLTAGE] [TEMP/HUMIDITY]
DIMMING / PHOTOCELL CHOOSE ONE ONLY
C US LISTED
TITLE 24
MADE in U.S.A.
5 YEAR WARRANTY