Installation Guide

ManualsBrandsLithonia Lighting ManualsArea Lights4700-Lumen Gray Integrated LED Area Light

page 1

If this ﬁ xture fails to operate properly, use the guide below to

diagnose and correct the problem.

Trouble Shooting Guide

• Verify that power is turned on at switch and breaker

• Verify that ﬁ xture is wired properly

• Verify that line voltage is correct.

• Test if Photocontrol works properly

The photocontrol in this ﬁ xture is designed to turn on ﬁ xture

light at low light levels.

If light does not come on or stays on:

Test if Photocontrol works properly:

• Cover Photocontrol - Light should come on.

• Shine a ﬂ ashlight into Photocontrol - Light should go off.

If ﬁ xture cylcles on and off:

Light reﬂ ecting back off any surrounding surfaces enters the

photocontol. To correct problem, reposition the ﬁ xture or eliminate

reﬂ ective surface.

If further technical assistance is required, contact: Technical

Support at: (800) 279-8041

This LED light provides low maintenance service with no bulbs

to change. Clean surfaces with mild soap and water. Do not use

abrasive materials such as scouring pads or powders, steel wool

or abrasive paper.

WARNING: There are no user serviceable parts inside ﬁ xture.

INSTALLATION INSTRUCTIONS

UTDDLED2_Rev 7/14

Protect yourself. Before installing, read the entire instructions

carefully and save them for future reference.

Date installed:________________________________________

FIXTURE PACKING LIST

Description Quantity

1) Housing Assembly ............................................................... 1

2) Photocontrol ........................................................................ 1

3) 1” Bolts* ............................................................................... 2

4) 2” Wood Screws* ................................................................. 3

5) Cover Plate* ........................................................................ 1

6) Wire Nuts* ........................................................................... 3

7) Diffuser* ............................................................................... 1

*Contained in parts packs

Mounting Hardware Included

Waterproof Supply Fittings & Conduit

will be required - Purchase Separately

Silicone Sealant Required

REQUIRED TOOLS:

Dusk to Dawn LED Area Light

Model Number(s):

TDD LED 2

Summary of content (9 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Dusk to Dawn LED Area Light Model Number(s): TDD LED 2 Protect yourself. Before installing, read the entire instructions carefully and save them for future reference. Date installed:________________________________________ FIXTURE PACKING LIST Description Quantity 1) Housing Assembly............................................................... 1 2) Photocontrol ........................................................................ 1 3) 1” Bolts* ............................
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW THESE SAFETY INSTRUCTIONS! • To reduce the risk of death, personal injury or property damage from ﬁre, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the ﬁxture box and all ﬁxture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
PAGE 3
INSTALLATION INSTRUCTIONS 1. Remove ﬁxture components and parts pack. Check to ensure all parts are included. Note: Account for small parts and destroy packing material, as these may be hazardous to children. 2) Photocontrol Figure A 1) Housing Assembly Turn OFF Power at circuit breaker box! CAUTION: Do not rely on wall switch alone to turn off power. Note: NOT suitable for use with dimmers, motion sensors or other remote devices. 2.
PAGE 4
E S PA Ñ O L GUÍA DE PASO-A-PASO Crepúsculo al Amenecer - Area la Luz LED Model Number(s): TDD LED 2 Antes de instalar, lea estas instrucciones cuidadosamente y guárdelas para futura referencia. Fecha Instalada:_______________________________ LISTA DE EMBALAJE Descripción Cantidad 1) Ensamblaje de la Carcasa .................................................. 1 2) Fotocontrol .......................................................................... 1 3) Tornillos de 1”* ...................................
PAGE 5
E S PA Ñ O L INFORMACIÓN IMPORTANTE DE SEGURIDAD LEA Y SIGA LAS INSTRUCCIONES DE INSTALACIÓN. • Para reducir el riesgo de muerte, lesiones personales o daño a la propiedad que pueda surgir de incendios, choques eléctricos, cortes, abrasiones, caída de partes y otros peligros lea todas las advertencias e instrucciones incluidas en la caja o su interior, además de las etiquetas del montaje. • Antes de instalar o revisar el equipo, o realizar mantenimiento de rutina, siga estas precauciones generales.
PAGE 6
E S PA Ñ O L GUÍA DE PASO-A-PASO 1. Quite los componentes del luminario y el paquete de piezas. Veriﬁque que todas las piezas estén incluidas. Nota: Tenga cuidado con las piezas pequeñas y destruya el material de embalaje, ya que pueden ser peligrosos si están al alcance de niños. 2) 1) ¡Apague la electricidad en la caja de rtacircuitos! ATENCIÓN: No se conﬁe de cortar la corriente en el interruptor mural solamente.
PAGE 7
Français DIRECTIVES D’INSTALLATION Crépusculaire - Éclairage de Périmètres Numéro des modèle TDD LED 2 Pour votre propre protection. Avant de procéder à l’installation, veuillez lire attentivement ces directives et les conserver pour référence ultérieure. Date de l’installation :__________________ LISTE DES PIÈCES Description Quantité 1) Bloc boîtier .......................................................................... 1 2) Cellule photoélectrique ....................................................
PAGE 8
Français IMPORTANTES MESURES DE SÉCURITÉ VEUILLEZ LIRE ET RESPECTER TOUTES LES CONSIGNES DE SÉCURITÉ! • Aﬁn de réduire le risque de blessures personnelles ou de mort, ou d’endommager le matériel en raison d’un incendie, d’un choc électrique, de la chute de pièces, de coupures/abrasions ou de tout autre danger, lisez tous les avertissements et instructions compris dans et sur la boîte de la ﬁxation et toutes ses étiquettes.
PAGE 9
Français GUIDE DÉTAILLÉ 1. Retirer les composants de l’appareil et l’emballage des pièces. S’assurer que toutes les pièces sont incluses. Note: Faites attention aux petites pièces et détruisez le matériel d’emballage car ils pourraient être dangereux pour les enfants. 2) 1) Couper l’électricité au fusible ou au disjoncteur! ATTENTION: Ne coupez pas le courant uniquement au niveau de l’interrupteur mural.