Datasheet

TDS LOCTITE
®
243™, March-2010
Heat Aging/Hot Strength
Aged under conditions indicated and tested at temperature
% Initial Strength @ 22 °C
Exposure Time, hours
120
100
80
60
40
20
0
0 200 400 600 800 1000
100 °C
120 °C
150 °C
180 °C
200 °C
Chemical/Solvent Resistance
Aged under conditions indicated and tested @ 22 °C.
% of initial strength
Environment °C 500 h 1000 h
Motor oil 125 110 115
Unleaded gasoline 22 100 95
Brake fluid 22 105 110
Water/glycol 50/50 87 120 125
Acetone 22 85 85
Ethanol 22 95 90
E85 Ethanol fuel 22 95 100
B100 Bio-Diesel 22 110 110
Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m:
M10 Stainless steel nuts and bolts
% of initial strength
Environment °C 500 h 1000 h
Sodium Hydroxide, 20% 22 105 105
Phosphoric Acid, 10% 22 110 105
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use:
For Assembly
1.
For best results, clean all surfaces (external and internal)
with a LOCTITE
®
cleaning solvent and allow to dry.
2. If the cure speed is too slow, use appropriate activator.
Please see the Cure Speed vs. Activator graph for
reference. Allow the activator to dry when needed.
3. Shake the product thoroughly before use.
4. To prevent the product from clogging in the nozzle, do
not allow the tip to touch metal surfaces during
application.
5. For Thru Holes, apply several drops of the product onto
the bolt at the nut engagement area.
6. For Blind Holes, apply several drops of the product to
the lower third of the internal threads in the blind hole, or
the bottom of the blind hole.
7. For Sealing Applications, apply a 360° bead of product
to the leading threads of the male fitting, leaving the first
thread free. Force the material into the threads to
thouroughly fill the voids. For bigger threads and voids,
adjust product amount accordingly and apply a 360°
bead of product on the female threads also.
8. Assemble and tighten as required.
For Disassembly
1. Remove with standard hand tools.
2. In rare instances where hand tools do not work because
of excessive engagement length, apply localized heat to
nut or bolt to approximately 250 °C. Disassemble while
hot.
3. Apply localized heat to the assembly to approximately
250 °C. Disassemble while hot.
For Cleanup
1. Cured product can be removed with a combination of
soaking in a Loctite solvent and mechanical abrasion
such as a wire brush.
Loctite Material Specification
LMS
LMS dated June-29, 2009. Test reports for each batch are
available for the indicated properties. LMS test reports include
selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Henkel Americas
+860.571.5100
Henkel Europe
+49.89.320800.1800
Henkel Asia Pacific
+86.21.2891.8863
For the most direct access to local sales and technical support visit: www.henkel.com/industrial