SDS

ManualsBrandsLoctite ManualsPaint9 fl. oz. White 2-in-1 Seal and Bond Premium All Condition Sealant

Safety Data Sheet

Revision Number: 001.1

Issue date: 12/12/2014

IDH number: 1900055

Product name: Loctite Premium 2in1 Seal & Bond

Page 1 of 6

1. PRODUCT AND COMPANY IDENTIFICATION

Product name:

Loctite Premium 2in1 Seal & Bond

IDH number:

1900055

Product type:

Joint sealant, polymer silan-modified

Restriction of Use:

None identified

Region:

United States

Company address:

Contact information:

Henkel Corporation

One Henkel Way

Rocky Hill, Connecticut 06067

Telephone: +1 (800) 624-7767

MEDICAL EMERGENCY Phone: Poison Control Center 1-877-671-

4608 (toll free) or 1-303-592-1711 TRANSPORT EMERGENCY

Phone: CHEMTREC 1-800-424-9300 (toll free) or 1-703-527-3887

2. HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW

WARNING:

MAY CAUSE AN ALLERGIC SKIN REACTION.

CAUSES SERIOUS EYE IRRITATION.

HARMFUL IF INHALED.

HAZARD CLASS

HAZARD CATEGORY

ACUTE TOXICITY INHALATION

EYE IRRITATION

SKIN SENSITIZATION

PICTOGRAM(S)

Precautionary Statements

Prevention:

Avoid breathing dust or fumes. Wash thoroughly after handling. Use only outdoors or in a well-

ventilated area. Contaminated work clothing should not be allowed out of the workplace. Wear

eye and face protection. Wear protective gloves.

Response:

IF ON SKIN: Wash with plenty of soap and water. IF INHALED: Remove person to fresh air and

keep comfortable for breathing.

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if

present and easy to remove. Continue rinsing. Call a poison control center or physician if you

feel unwell. If skin irritation or rash occurs: Get medical attention. If eye irritation persists: Get

medical attention. Wash contaminated clothing before reuse.

Storage:

Not prescribed

Disposal:

Dispose of contents and/or container according to Federal, State/Provincial and local

governmental regulations.

Classification complies with OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of the

United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).

See Section 11 for additional toxicological information.

3. COMPOSITION / INFORMATION ON INGREDIENTS

Hazardous Component(s)

CAS Number

Percentage*

Summary of content (6 pages)

PAGE 1
Safety Data Sheet Revision Number: 001.1 Issue date: 12/12/2014 1.
PAGE 2
Calcium carbonate Titanium dioxide Silane derivative 471-34-1 13463-67-7 Proprietary 30 - 60 1-5 1-5 * Exact percentage is a trade secret. Concentration range is provided to assist users in providing appropriate protections. Exposure to moisture during cure will release 1-2% methanol. 4. FIRST AID MEASURES Inhalation: Move to fresh air. If symptoms persist, seek medical advice. Skin contact: Wash with soap and water. If skin irritation persists, call a physician.
PAGE 3
8. EXPOSURE CONTROLS / PERSONAL PROTECTION Employers should complete an assessment of all workplaces to determine the need for, and selection of, proper exposure controls and protective equipment for each task performed. Hazardous Component(s) ACGIH TLV OSHA PEL 10 mg/m3 TWA Total dust. Calcium carbonate Titanium dioxide 10 mg/m3 TWA Silane derivative None 5 mg/m3 PEL Respirable fraction. 15 mg/m3 PEL Total dust. 15 mg/m3 PEL Total dust.
PAGE 4
10. STABILITY AND REACTIVITY Stability: Stable under normal conditions of storage and use. Hazardous reactions: Will not occur. Hazardous decomposition products: Methanol is liberated slowly upon exposure to moisture. Incompatible materials: Oxidizing agents. Reactivity: Not available. Conditions to avoid: Exposure to moisture. 11.
PAGE 5
13. DISPOSAL CONSIDERATIONS Information provided is for unused product only. Recommended method of disposal: Follow all local, state, federal and provincial regulations for disposal. Hazardous waste number: It is the responsibility of the user to determine if an item is hazardous as defined in the Resource Conservation and Recovery Act (RCRA) at the time of disposal. Product uses, transformations, mixtures, processes, etc.
PAGE 6
Prepared by: Mary Ellen Roddy, Sr. Regulatory Affairs Specialist Issue date: 12/12/2014 DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods Henkel has no control.