Product manual Firstly, regarding your purchase of our company's products, Express our sincerest gratitude! Please read this manual carefully before use, In order to use the product correctly.
Bill of Material category number complete machine 1 Remote control 1 instructions 1 Plastic flange 1 Rubber flange 1 Hexagonal hose 1 Hexagonal triangular valve 1 Fixed flange screws 4 Ceramic fixing screws 2 Screw expansion seed 4 Screw decorative cover 2 1
Nstallation and commissioning 1. Open the angle valve Remove debris from the tank duct (Kind reminder: When opening for the first time, the angle valve handle has a large torque) 2. Power connection Insert the power cord leakage protection plug into the power socket and press the reset switch. The plug indicator light is on, indicating that the power is turned on. reminder: Press the leakage test button before use, and the reset switch will pop up to indicate leakage The protection function is normal.
Toilet installation Precautions before installation Minimum dynamic working water pressure: 0.09 MPa or higher (3.96 gallons)/min (15Lmin) or higher. Failure to meet this pressure will not achieve the best flushing effect. Note: If you do not have a water pressure testing device, please use the following method Hoses in packaging ground Corner valve inside the packaging Water storage bucket inlet Sewage discharge When the water volume exceeds 0.
Knob Function Description cease 1. Press and hold the "knob" button (3s) on the machine to enter shutdown mode (the display screen turns off), and then press the "stop" button to return the machine to working mode. In shutdown mode, except for the "stop" button on the host, any button (including the host and remote control) is invalid. 2. When the user sits down, press the "Stop" button on the host to stop the female washing and hip washing and drying functions.
Flip/flip Spray rod Night light self-cleaning Feminine Stop/flushButt wash cleansing dry Water Position reduction shift back Child Hydraulic Position cleaning loading forward Wind temperature Seat temperature Water temperature Remote control diagram Matters needing attention: If the toilet you purchased has an automatic opening/closing function, the remote control is shown in the above picture.
LED 1. When the unit starts, the seat temperature will be displayed by default. 2. When adjusting the water temperature, the display screen shows the water temperature adjustment, and there is seat temperature adjustment.
Seat ring function E 16 Race Heating seat ring Toilet flushing surface temperature 4 Different levels of adjustment heating power 45W Opening and closing device Silent soft shutdown device Heating combustion protection The seat temperature automatically drops to level 1 within 10 minutes of use Safety devices Sensing area, temperature sensor, temperature fuse, over temperature protection, leakage protection plug Automatic cleaning When the user leaves the toilet, the toilet will automatically
Triangle valve cleaning method Maintenance of filter screen Maintenance time: Normal water pressure, but poor flushing performance 1. Turn off the power and angle valve 2. Unscrew the corner valve nut Filter nut 3. Removing the filter screen valve body filter screen 4. Use a brush to clean the filter screen 5. Flush and install filter screen and angle valve 6. Open the angle valve and connect the power supply. After self inspection, it can work normally.
Routine maintenance Maintenance and upkeep of main equipment 1. Before conducting maintenance, please turn off the power supply. 2. Wipe off the stains with a soft damp cloth. 3. Safety self inspection After cleaning, rinse and connect the toilet to the power supply. Maintenance and upkeep of nozzles 1. Nozzle self-cleaning When not sitting on the machine, briefly press the "Back/Move" self-cleaning button on the host, the nozzle will extend outward, and water will flow out. 3.
Product specifications Rated voltage 110V to 120V, 50V to 60Hz Rated power 1500w Overall unit waterproofing IPX4 wire Approximately 1.5 meters in length Flushing volume 1.6/1.1Gpf (full flush 6.0h) Flushing mode Siphon jet Rough machining distance 305 mm Main unit toilet Outlet outer diameter ≤ 100mm Drainage method Undershoot Water pressure range 0.09Mpa (dynamic water pressure, flow rate), 3.96 gallons per minute (15.0 liters per minute or higher) -0.
Handling methods for cover plate faults problem There is no water in the nozzle reason Solution Blockage caused by bent water inlet hose Solve the problem of water inlet hose bending Inlet valve closed Open the inlet valve Press the water supply system and wait for water supply The water inlet hose is bent, causing Solve the problem of water inlet hose partial blockage bending Water supply cut off Weak water cleaning water temperature is low Inlet valve not fully open Fully open the inlet valve
Important safeguard measures When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following: 1. This device is not allowed to be used by weak individuals (including children). Sensory or spiritual abilities, or lack of experience and knowledge, unless they receive supervision or guidance. 2. Children under guardianship are not allowed to play with this device.Children aged 3.
Important safety instructions ！ Attention - Failure to follow the instructions may result in physical injury or property damage. 1. Do not install or use this product in damp areas such as steam rooms. 2. It is recommended to use a waterproof power socket and install it in a place that is not easily affected by moisture. 3. This product is only suitable for currents of 110V-120V, 50/60Hz, with a load current of at least 15A.
