WASHING MACHINE MESIN CUCI WH 262 USER MANUAL GB TH 35.292.
Contents Technical specifications Warnings Disposal Tips for environmental protection Description of the appliance 2 3 3 4 4 Detergent dispenser drawer Laundry weights Removing stains Detergents and additives Quantity of detergent to be used International wash code symbols 10 Maintenance 11 Bodywork Detergent dispenser drawer Cleaning of the drainage area Water inlet filter Emergency emptying out 4 Use 5 Control panel Controls 5 5 Operating sequence Washing programmes Washing hints Something not
The following warnings are provided in the interests of overall safety. You must read them carefully before installing or using the appliance. • Leave the porthole door slightly ajar when the appliance is not in use. This preserves the door seal and prevents the formation of musty smells. • Always check that water has emptied out before opening the door. If not, drain the water following the instructions in the instruction book. • Always unplug the appliance and shut the water tap after use.
Tips for environmental protection To save water, energy and to help protect the environment, we recommend that you follow these tips: • With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature. • Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!).
Use ENGLISH Control panel 1. Programme chart 6. Temperature selector It will help you to choose the most suitable washing programme for your laundry. This control allows you to select the temperature of the washing cycle in accordance with the kind of clothes to be washed. Turn the control until the required temperature coincides with the marker. On the program table you will find the most appropriate temperature for each kind of washing. Selecting any program can be run through with cold water.
4. Select the temperature Operating sequence Turn the dial to the required setting. Before washing your first load of laundry, we recommend that you run a cotton cycle at 60°C, with the machine empty, in order to remove any manufacturing residue from the drum and tub. Pour half a measure of detergent into the main wash compartment and start up the machine. 80 1. Place the laundry in the drum R0032S Open the door. Place the laundry in the drum, one item at a time, shaking them out as much as possible.
Programme table ENGLISH Washing programmes for cotton and linen Load: 5 kg Additional functions DESCRIPTION Programme Temp.
Programme table Washing programmes for synthetics, mixed fabrics, delicates and wool Load: 2 kg, wool 1 kg Additional functions DESCRIPTION Programme Temp.
Sorting the laundry Removing stains Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens. Stubborn stains may not be removed by just water and detergent. It is therefore advisable to treat them prior to washing. Blood: treat fresh stains with cold water. For dried stains, soak overnight in water with a special detergent then rub in the soap and water.
Quantity of detergent to be used The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash programme. If using concentrated powder or liquid detergents, a programme without prewash must be selected. The washing machine incorporates a recirculation system which allows an optimal use of the concentrated detergent. Pour liquid detergent into the dispenser drawer compartment marked just before starting the programme.
1. Bodywork 3. Cleaning of the drainage area Clean the outside of the machine with warm water and a neutral, non-abrasive household detergent. Rinse with clean water and dry with a soft cloth. The drainage area must be cleaned if the pump has been blocked with objects such as buttons, safety pins, coins, etc. , or if lint has built up because clothes that generate lint have been washed at high temperatures. Important: do not use methylated spirits, solvents or similar products to clean the bodywork.
4. The water inlet hose filter If it takes longer to fill up the washing machine it is time to check the water inlet hose filter it may be clogged. Turn off the water tap. Unscrew the fixing nut of the inlet hose. Remove the filter from the electrovalve and clean it with a hard bristle brush and replace it. Screw on the nut thoroughfully. P0090 P0021 5.
Something not working? Problem • The machine does not start up: Possible cause • The door is not firmly closed. • The machine is not plugged in or there is no power at the socket. • The main fuse has blown. • The programme selector is not positioned correctly or the programme selector knob has not been pulled out. • The machine does not fill: • The water tap is closed. • The inlet hose is squashed or kinked. • The filter in the inlet hose is blocked. • The door is not properly closed.
Installation Transit security bars Before starting the machine up, the transport security bars must be removed as follows: You are advised to keep all the transport security bars in case the appliance has to be transported again. 1. Unscrew and remove the three rear screws by means of a key. 4. Unscrew and remove the four feet. Fit the grid on the bottom of the machine and refit the four feet. Tighten up the lock nuts on all feet. P0287 5.
B) If necessary turn the hose adequately by unscrewing the nut at the rear of the appliance. There should be a COLD WATER tap near the washing machine with a screwing on connection pipe of 3⁄4” gas for the water supply, a sink, a wash basin or a drainage system in the wall. Previously check if: — it is not a hot water tap. P0021 — the running water is clean. If not, run off a reasonable amount of water to flush out any debris that may have collected in the pipes.
60 cm. Min. 90 cm. Max. 1,5 m. Max. IMPORTANT: The distance from the floor to the highest part of the hose should be between 60 to 90 cm. (It is advised to be between 60 and 70 cm). The hose must not be bent nor twisted to avoid clogging. Should a prolongation of the discharging hose be unavoidable this must never surpass 1.5 m and must be of the same diameter as the original hose. Make sure the hoses are not too tense.
EHPOESL/Z - 02/2003
