Firmware Version 1.0.
Conduct an orchestra of lights. The Luxli Orchestra series can produce a dazzling symphony of light. Synchronize LED light units of all sizes, choose from millions of possible colors, apply lighting effects from four selectable modes, and control them instantly with the powerful Composer mobile app. For the latest version of the Composer mobile app, firmware updates, and a PDF of the full user manual, as well as videos and ideas for creative uses for the Taiko, visit luxlilight.com.
Precautions • Please read and follow these instructions, and keep this manual in a safe place. • Keep this product away from water and flammable gases or liquids. • Use only the correct, recommended voltage. • Do not attempt to disassemble or repair this product. • Clean this product with only a soft, dry cloth. • To avoid damage to this product, be careful not to overtighten or improperly thread any of the threaded fittings. • All images are for illustrative purposes only.
Overview 1 7 6 2 3 Back: 1. V-Mount battery plate 2. Power input 3. Micro-USB port for firmware updates (visit luxlilight.com for details) 4 4 5 4. 5. 6. 7. 5/8 in.
32% CCT 32% MODE 8 Control Panel: 8. Brightness dial 9. Power button 10. Mode selector 9 10 0% +/- GREEN 3900K 11 12 13 11. LCD screen 12. Function buttons 13. Adjustment dial Top: 14. Diffuser flap 15. Thumb tab 16. Barndoor slot 17.
Setting Up the Taiko Attaching the Tilt Lock Handle The tilt lock handle can be attached to either side of the Taiko.To attach the handle, follow these steps: 1. Place the Taiko and yoke down on a flat surface. 2. Use the Hex key to remove one of the tilt control screws, and replace with the tilt lock handle. Screw in the handle so the threads are engaged, but don’t tighten it. 3. Use the Hex key to tighten the control screw on the other side of the yoke.
Reversing the Receiver’s Locking Handle For mounting and handling convenience, you can change the side the locking handle is on: 1. Remove the Taiko from the light stand, and place it down on a flat surface. 2. Use a hex key to unscrew the center and outer mounting screws. 3. Turn the receiver so the handle is on the opposite side. 4. Replace the center and outer mounting screws and tighten until firm. Install/Remove the Diffuser The Taiko includes a medium-density diffuser.
User Interface Mode Selector Press the mode selector to cycle through the four operating modes: CCT, RGB, Filter, and Special Effects. Brightness Dial In all operation modes, the Brightness dial adjusts the brightness from 100% to 0% in 1% increments. In all operation modes, press the Brightness dial to toggle between the set brightness and 0%. Function Buttons The function buttons access the screen functions that are indicated next to the button.
CCT Mode CCT Adjustment screen Use the Adjustment dial to set a color temperature between 2800 and 10,000 K in 50 K increments. 32% CCT 32% 0% +/- GREEN 3900K Tint (+/− Green) Screen Tap the Function button next to “+/− Green” to access the Tint adjustment screen. 32% 3900K CCT +/- GREEN Use the adjustment dial to set the green/magenta color shift between +100% (full plus green) to −100% (full minus green) in 1% increments. 17% Press the CCT button to return to the CCT Adjustment screen.
RGB Mode Hue Adjustment Use the adjustment dial to set the hue from 0° to 360° on the color wheel.The crosshair icon moves horizontally to represent the location of the hue on the color wheel. Saturation Adjustment Tap the function button next to “SAT” to adjust saturation levels. Use the adjustment dial to set the saturation of the hue from 100% to 0% in 1% increments. The crosshair icon moves vertically to represent the level of saturation. Press the Hue button to return to the hue adjustment screen.
Filter Mode Filter Screen Use the adjustment dial to scroll through the 150 digital gel filters. Important! The selected filter is active only in Filter mode. CCT Adjustment Adjusts the base color temperature without leaving Filter mode. Tap the CCT function button to adjust the base color temperature using the adjustment dial. Press the Gel function button to change the active filter. 32% 54 3900 CCT Medium Purple Mauve Bright Pink FolliesPink Rose Pink Smokey Pink Scarlet S.
Special Effect Mode The Taiko is loaded with 10 animated special effects. Each effect has multiple parameters that can be adjusted in the edit menu. Special Effect Screen Use the adjustment dial to select one of ten preprogrammed effects by scrolling down the list and pressing the Play button . Pressing the Stop button stops the effect. Note: The LED panel turns off when Special Effects mode is selected.The LED panel will remain off until the effect is started.
Main Menu Press the function button for the main menu. The main menu can be accessed in all operating modes. Main menu Presets DMX Bluetooth About SELECT BACK The Presets Menu To save settings to a preset, do the following: 1. Scroll to the Presets menu with the Adjustment dial, and press the Select button. 2. Use the Adjustment dial to select a preset number, and press Save. Presets Save Preset A Preset B Preset C Load Preset D Factory default BACK 3. At the prompt, press Confirm.
The DMX Menu The Taiko offers 512 addresses. To set the DMX address: 1. Scroll to the DMX Address menu with the Adjustment dial, and press the Select button. DMX settings DMX Master Off DMX Address 1 DMX Mode CCT 8 bit SELECT 2. Use the Adjustment dial to select an address from 1 to 512, and press Save. BACK 3. At the prompt, press Confirm. To set the DMX mode, follow these steps: 1. Scroll to the DMX Mode menu with the Adjustment dial, and press the Select button. 2.
The Bluetooth Menu Access the Bluetooth menu to turn Bluetooth on or off. Bluetooth state Off On CONFIRM BACK The About Menu The About menu displays the Taiko’s serial number and firmware version. About Serial number 12FFB0006 Firmware version 1.0.
Specifications Light panel RGBAW LED Beam angle 76° (without diffuser) Bluetooth version 4.2 LE Battery mount V-mount (×2) Battery requirements 14.4–14.8 V, 10 A minimum per battery DC power input 4-pin XLR 24–36 V, 10 A Max power consumption 250 W Dimensions (W × H × D) 27 × 17.75 × 3 in. (68.6 × 45.1 × 7.6 cm) Weight (with yoke) 16.2 lb. (7.
Troubleshooting • If you encounter any problems, first try turning the device off and then on. • If the problem persists, remove the batteries or power supply for 15 seconds, and then restart. • Go to luxlilight.com to make sure you have the most recent firmware update. If a new firmware version is available, follow the instructions on how to download it to your light.
FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. Important: Changes or modifications to this product not authorized by Gradus Group could void the electromagnetic compatibility (EMC) and wireless compliance and negate your authority to operate the product.
One-Year Limited Warranty This LUXLI product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
luxlilight.
