Use and Care Manual

ASSEMBLY instructions
BEFORE YOU START
• WARNING: Due to the presence of small parts during assembly, keep out of reach of children until assembly
is complete. To prevent serious injury, children must not use the swing until properly installed.
• Assembly should be completed by adult person(s). We intend for our products to bring joy not frustration.
Because the Hammock Swing
TM
is meant to enjoy with friends too, we say invite a friend (or someone you can
spend at least 20 minutes with) to help you assemble and install your new swing.
• A flat level surface approximately 6 ft. x 4 ft. will be needed to spread out swing cover material for assembly.
• A wrench is included for tightening the four nuts.
installation instructions
TREE LIMB ASSEMBLY: Test tree limb to ensure that it will hold
the weight limit of
300 lbs. safely.
SWING SET OR OTHER HORIZONTAL BEAM ASSEMBLY:
Attach swing to a swing set by removing two sets of swings from
the existing swing set and attach the four metal loops to the
swing support hook hardware installed on equipment or
optional carabiners/spring clips.
1. Do not install home playground equipment over concrete,
asphalt, packed earth, grass, carpet or any other hard
surface.
A fall onto a hard surface can result in serious injury or death
to the equipment user.
2. To prevent serious injury, children must not use the
equipment until properly installed.
3. Confirm that the supporting structure is secure, it will support
at least 300 lbs., is over level ground, has a minimum height
of 7 ft. and is no less than 6 ft. on all sides from vertical
elements. Swing should have a clearance of at least 1.5 times
the total length of all the rope measured from the tree
limb/horizontal beam to the spring clip(s) attachment point.
4. Adjust swing hanging length so platform is parallel with
ground. Bottom of swing should be no more than 24 in. and
no less than 18 in. from the ground.
1. Lay out all necessary swing components
pictured above.
2. Unfold material swing cover on level surface with design
facing up. Pull the four hook/loop straps toward the center
so the fastening side faces up.
3. Connect a one-end shrinked straight tube (with metal pin)
with a two-end shrinked straight tube. Depress metal pin
with thumb to slide end into tube, pin will pop through
hole and hold tubes together. This creates the side length
tube. Slide through swing cover sleeve. Repeat this step
on second side with remaining two poles.
Insert the narrow ends of the side sections with the wider
ends of the curved-tubes that come pre-inserted in the
sleeves at ends of cover.
ASSEMBLY
4. Remove the nut and one
washer from the bolt
assemblies at the end of the
hanging ropes. Pull the bolt
ends of each rope through the
slot at the end of the straps.
One washer will remain on
top of the tube threaded onto
the bolt. Insert the bolt
through the holes formed at
the tubes connection points.
5. Add washer and nut to
the bottom side of tube
bolt and secure. Tighten
with included wrench.
Repeat Steps 4 and 5 on
the remaining three
straps with remaining
three bolt ends.
6. Pull the hook/loop straps back over the tubing
frame and attach to the hook/loop fastener on
underside of swing.
7. Finished swing should look as pictured above.
Ropes should not cross each other above swing.
adjusting swing height
Adjust swing hanging length so bottom of swing when rider is in it is parallel with the ground. Bottom of swing with rider
on it should be no more than 24 in. and no less than 18 in. from the ground.
This swing is made to enjoy like a hammock. We hope you enjoy kicking back and relaxing in it. In the same spirit, please
enter and exit the swing as you would a hammock — carefully.
Ensure that the swing hangs horizontal after adjustment of the ropes.
18 inch minumum to 24 inch maximum
ground clearance
Optional
Tree Strap
Optional
carabiner
Rope
At least 6 feet
from trunk
or 1½ times
the length
of the swing’s rope