Installation guide

iNSTALLATiON REQUIREMENTS
Tools and Parts
Gather the recommended tools and parts before starting
installation• Read and follow the instructions provided with any tools
listed here.
All Installations
Tools needed:
_,. Flat-blade
screwar!ver
•
5 _ 1
_6 and V4 _ UL histed/CSA _ n
nut drivers or _._Y" Approved twist-on U W
hex sockets i.y wire connectors* -- --
10 adjustable wrench s.,, ,, ..... ,4 _..-_
that opens to wrench _
11/8" (2.9 cm) _ .
*Must be the proper size to connect your household wiring to 16
gauge wiring in dishwasher
Other useful items you may need:
Flashlight _ Bath towel
Parts supplied:
Drainhos_C!amps(2)_rainhose #10x1¢
(! laige and I Small)I Phi!!ips-head
screws (2)Green
Make sure all these parts are included in the literature package.
Parts needed:
Compr x _ Hose Fatting
FOr part or kit, see local
retailer or call Whirlpool
Parts: 1-800-442.9991, Part
Number w10273460
Other parts you may also need:
11V£"_2,': : _ Sidem%unti_g kiWI Masking or_
(3811 z5cm) _ for solid surface duct tape I
screw_type I c°unter_°ps I I
I clamps (3 maximum)18212560)!_-art lyU.mDe r [ I
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See "Electrical
Requirements" section. It is recommended that electrical connections be
made by a licensed electrical installer.
In addition, for first time installations
Tools needed:
Cordk
with W!, 3/41'
and 1Wi hole
saw bits
Parts needed:
I
Copper tubing (%" See '_Electrical Requirements" section
O.D.suggested) or i . .
flexible braided F0rD,rectVV!re: ForP0wer Supply
cater su.._.l, lin _ useUL Listed/ Cord: use UL
CSA Approved liste d power
_/f----__,_'_\ strain _elief SUPPLY cord kit
(,(.[t[.[L .)))))),)} to fit Y8 (2.2 cm)marked for use
hg!e W!!h d!shwasher
Location Requirements
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor should not
touch the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by the
wa rra nty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277)is available
from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The
location must provide:
• easy access to water, electricity and drain.
• Convenient access for loading and unloading dishes. Corner
locations require a 2" (5.1 cm) minimum clearance between the
side of the dishwasher door and the wall or cabinet.
• square opening for proper operation and appearance.
• cabinet front perpendicular to floor.
• level floor. (If floor at front of opening is not level with floor at
rear of opening, shims may be needed to level dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the dishwasher
opening is uneven (example: flooring extends only partway into
opening).
NOTE: To avoid shifting during dishwasher operation.
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Product and Cabinet
Opening Dimensions" section.