PP2 User Guide

1. Insert Split Flanged Bushing into center hole of Sign Base
making sure to orient it so that the larger ends with the screw
holes are perpendicular to the Ballast Ports.
2. Attach the 2 Pole Stops using the pre-drilled holes about 12” up
from the bottom on the Sign Pole using the Stainless Steel
Screws provided; the screw fits into the inside of the cup side.
The 3rd stop is an extra.
3. Insert the Pre-Drilled Sign Pole into center hole of base through
the Split Flanged Bushing using a twisting motion while pressing
down until the Pole Stops make contact with the Split Flanged
Bushing. Make sure the end of the pole with the 6 mounting
holes is facing up.
4. Put the Security Bolt into the hole on the side of the Sign Base
and screw in firmly; Do Not over-tighten.
5. Add 2-3 gallons of water to the base using one of the Ballast
Ports, for stability and wind resistance; the complete sign will
weigh 25-35 lbs.; 30-40 pounds of sand can be substituted for
the water for additional stability.
6. Insert the EZ-Grip Finial into the top of the Sign Pole and align
the holes in the pole with the holes in the finial. Most signs
require the finial to be inserted all the way; for signs with the
hole 3” from the top of the sign use the bottom hole on the finial.
7. Attach the top of the sign face to the top hole in the Sign Pole
using the hardware provided. Make sure to place the Stabilizer
Plate between the back of the sign and the Sign Pole with the
flat side facing the sign and the rails running along the length of
the Sign Pole. The Mounting Plate Bolt will go through the pole
and the finial. Attach a Stabilizer Plate to the end of the
Mounting Bolt projecting out of the Sign Pole and finger-tighten
the Flange Nut.
8. Attach the bottom of the sign face to the Sign Pole using the
hardware provided following the same directions in step 2.
You may have to wiggle the sign to align the holes that are on 3”
centers starting 9” from the top hole.
9. Tighten the Flange Nuts snuggly; Do Not over-tighten, crush or
distort the Sign Pole. The Flange Nuts have serration’s that will
hold tight.
10. For 2 sided signs place the second sign face between the back
Stabilizer Plate and the Flange Nut. For thick sign panels a
longer 5/16” bolt may be required.
11. To move the sign simply grip the Finial handle, tip the
sign on its recessed wheels and pull to roll in, out or about.
NOTE: The ‘TIP-N-ROLL’™ Portable Pole 2 Sign Holder accommodates all stock street, safety, directional and other signs from 9”x12 to
24”x24” plus 12”x36” along with custom shaped sign panels. POP pole signs that attach with zip ties can also be used.
CAUTION: ‘TIP-N-ROLL’™ Portable Pole 2 Sign Holders are designed for winds up to 30-40 mph. In the event of higher winds bring sign
inside or add more ballast.
Manufactured by Joseph Struhl Company, Inc. PO Box N, Garden City Park, NY 11040
1-800-552-0023 • 516-741-3660 • Fax [phone] • www.magicmaster.com
© 2007 - 2016 Joseph Struhl Company, Inc.
Inst:PP2 inst
Portable Pole 2
Sign Holder
USER GUIDE
Split Flanged
Bushing (1)
Pole Stop (3)
Mounting
Plate Bolt
(5/16”) (2)
Stainless
Screws (2)
Flange Nut (2)
Smooth-Edge
Stabilizer
Mounting Plate (4)
Security Bolt
(1/4”) (1)
EZ-Grip
Finial
Portable Pole 2
Rolling Sign
Base
Split Flanged
Bushing
48” Pre-drilled Pole
Ballast
Ports
Security
Bolt
Pole Stop
Stainless
Screw
EZ-Grip
Finial
EZ-Grip
Finial
Stabilizer
Mounting
Plates
Flange Nut
Mounting
Plate Bolt
(5/16”)