Owners manual

ManualsBrandsMagnaflow Performance Exhaust ManualsAutomotive700002 Performance Exhaust Headers

BILL OF MATERIALS:

SHOP SUPPLIES:

MINIMUM REQUIRED TOOLS:

To ease removal of existing exhaust components

(especially on older vehicles) spray penetrating lubricant

on all fasteners and hangers/insulators that will be

loosened or removed and let soak before disassembly.

SPRAY LUBRICANT

WEAR SAFETY

GLASSES

READ INSTRUCTIONS

THOROUGHLY BEFORE

INSTALLING PRODUCT

MAGNAFLOW RECOMMENDS PROFESSIONAL INSTALLATION ON ALL THEIR PRODUCTS

WARNING: When working on, under, or around any vehicle exercise caution. Please allow the vehicle's

exhaust system to cool before removal, as exhaust system temperatures may cause severe burns. If working

without a lift always consult vehicle manual for correct lifting specifications. Always wear safety glasses and

ensure a safe work area. Serious injury or death could occur if safety measures are not followed.

ATTENTION: Always install any supplied band or U-bolt clamps to the proper torque specifications of 40-45

ft-lbs for band clamps and 30-35 ft-lbs for U-bolt clamps. Over tightening will result in the clamp breaking and

will NOT be warranted by MagnaFlow.

MAGNAFLOW: 22961 Arroyo Vista - Rancho Santa Margarita, CA 92688 | 1(800) 990-0905

Technical Support: 1(800) 959-9226 | Email: moreinfo@magnaflow.com

16mm Socket

15mm Socket

14mm Socket

10mm Socket

7/8" Wrench

Pry Bar

PART NO. 700002

'98-'99 Chevy Camaro/Pontiac Firebird 5.7L

1. D/S HEADER ASSY

2. P/S HEADER ASSY

1. [12] M8-1.25 HEADER BOLT

2. [6] M10-1.25x40mm BOLT

3. [6] M10-1.25 NUT

4. [6] 7/16" WASHER

5. [1] OUTLET GASKET D/S

6. [1] OUTLET GASKET P/S

7. [2] A.I.R. GASKET

8. [1] E.G.R. GASKET

9. [1] SPARK PLUG WIRE 45deg

10. [2] MANIFOLD GASKET

HARDWARE KIT:

ANTI-SEIZE THREAD

COMPOUND FOR

ALUMINUM HEADS

Summary of content (3 pages)

PAGE 1
'98-'99 Chevy Camaro/Pontiac Firebird 5.7L PART NO. 700002 BILL OF MATERIALS: 1 2 1. D/S HEADER ASSY 2. P/S HEADER ASSY SHOP SUPPLIES: HARDWARE KIT: ANTI-SEIZE THREAD COMPOUND FOR ALUMINUM HEADS SPRAY LUBRICANT WEAR SAFETY GLASSES READ INSTRUCTIONS THOROUGHLY BEFORE INSTALLING PRODUCT To ease removal of existing exhaust components (especially on older vehicles) spray penetrating lubricant on all fasteners and hangers/insulators that will be loosened or removed and let soak before disassembly. 1.
PAGE 2
Step 3. Using a 16mm socket unbolt the dipstick Step 1. Before removing the OEM manifold system, first disconnect the battery. Next remove all spark plug wires from the coils and the plugs, and then set aside. Using a 10mm socket unbolt the coil pack brackets from the driver side and passenger side and carefully flip them up towards the motor to keep out of the way. Using a 5/8" socket remove all of the spark plugs for clearance. assembly from the passenger side of the vehicle and remove. Step 4.
PAGE 3
Step 5. Install your new header assemblies with the supplied gasket and header bolts to the manufacturers torque specifications. Reinstall the AIR connection on the drivers side assembly and the EGR and AIR pipes on the passengers side header assembly using the supplied gaskets. Step 7. Reinstall the spark plug wires to the ignition coils and the spark plugs. You will need to use the supplied 45deg spark plug wire to replace the OEM one located on the passengers side nearest the fire wall (Cylinder # 8).