Installation Manual
Page 48
© 2015 Sensata Technologies
Appendix A – Specifi cations and Optional Equipment
Appendix A – Specifi cations and Optional Equipment
A-1 Inverter/Charger Specifi cations
Models ME2000 (-15B, -20B) ME2012 (-15B, -20B) ME2512 ME3112
Inverter Specifi cations
Input Battery Voltage Range 9 to 16 VDC 9 to 16 VDC 9 to 16 VDC 9 to 16 VDC
Absolute Maximum DC Input 25 VDC 25 VDC 25 VDC 25 VDC
AC Output Voltage Accuracy 120 VAC ±5% (≤ continuous power)
Output Frequency and Accuracy 60 Hz ± 0.1 Hz
Continuous Power Output (@ 45°C) 2000 VA 2000 VA 2500 VA 3100 VA
Continuous AC Output Current 17 A 17 A 21A 26 A
1 msec Surge Current (AAC) 60 60 100 120
100 msec Surge Current (AAC) 37 37 45 50
5 sec Surge Power (real watts) 3700 3700 5000 6000
30 sec Surge Power (real watts) 3450 3450 4500 4800
5 min Surge Power (real watts) 3100 3100 3500 3950
30 min Surge Power (real watts) 2400 2400 2900 3500
Rated Input Battery Current 266 ADC 266 ADC 333 ADC 413 ADC
Inverter Effi ciency (peak) 95% 95% 91% 90%
HBCO/HBCI ≥15.8 VDC
LBCO/LBCI 9.0 VDC (adj)/12.5 VDC
Series Stacking 120/240 VAC No
Transfer Time 16 msecs
Search Mode (typical) 5 watts
No Load (120 VAC output, typical) 20 watts 20 watts 23 watts 25 watts
Waveform Modifi ed Sine Wave
Charger Specifi cations
Continuous Output at 45°C 100 ADC 100 ADC 120 ADC 160 ADC
Input Current - Rated Output (AAC) 15 15 18 22
Charger Effi ciency 85%
AC Input Frequency Range 50 to 70 Hz
AC Input Voltage Range 60 to 140 VAC (120 VAC nominal)
Power Factor > 0.95
General Features and Capabilities
Transfer Relay Capability Single leg in at 30 amps Two input legs at 30 amps each, or combine for 60 amps*
Five-stage Charging Capability Bulk, Absorb, Float, Equalize (requires remote), and Battery Saver™
Battery Temp Compensation Yes, 15 ft Battery Temp Sensor standard
Internal Cooling 0 to 120 cfm variable speed drive using dual 92 mm brushless DC fan
Overcurrent Protection Yes, with two overlapping circuits
Over-temperature Protection Yes, on transformer, MOSFETS, and battery
Corrosion Protection PCB’s conformal coated, powder coated chassis/top, and stainless steel fasteners
Safety Listings ETL listed to UL/cUL 458, and CSA C22.2 # 107.1-01
Warranty 3 years parts and labor
Dual Branch-Rated Output Breakers Optional on ME2000 (15 or 20 amp breakers) or ME2012 (15 or 20 amp breakers)
Environmental Specifi cations
Operating Temperature -20°C to +60°C (-4°F to 140°F)
Non-operating Temperature -40°C to +70°C (-40°F to 158°F)
Operating Humidity 0 to 95% RH non-condensing
Physical Specifi cations
Unit Dimensions (h x w x d) 13.75” x 12.65” x 7.0”
(34.9 cm x 32.1 cm x 17.8 cm)
13.75” x 12.65” x 8.0”
(34.9 cm x 32.1 cm x 20.3 cm)
Shipping Dimensions (h x w x d) 19” x 15” x 13” (48.3 cm x 38.1 cm x 33 cm)
Mounting Shelf (top or bottom up) or wall (no uncovered vents on top or bottom)
Unit Weight 37 lb (16.8 kg) 37 lb (16.8 kg) 41 lb (18.6 kg) 46 lb (20.9 kg)
Shipping Weight 45 lb (20.4 kg) 46 lb (20.9 kg) 51 lb (23.1 kg) 56 lb (25.4 kg)
Max operating altitude 15,000’ (4570 m)
Specifi cations @ 25°C (unless otherwise noted) - Subject to change without notice.
* The pass-thru capability on each leg of the -15B and -20B models is limited by the output breaker size on each output.