User manual

ManualsBrandsMakita ManualsNetwork Router3612B

Rout LiftR

User Manual

Model #02001

Thank you for choosing this product from

JessEm Tool Company. We appreciate your

support and hope that our product serves you

well. This product is designed to provide

many years of reliable service provided it is

used as intended and taken care of.

This user manual will assist you in assembly

and general operation of this product. It is

not our intent to teach you about

woodworking. It is assumed that you are an

experienced woodworker with the basic skills

and experience necessary to use this product

safely. If after reading the following

instructions, if you are unsure or

uncomfortable about safely using this

product we urge you to seek additional

information through widely available

woodworking books or classes.

As part of our Continuous Product

Improvement Policy, JessEm products are

always advancing in design and function.

Therefore there may be differences between

what is shown in our catalogs, website or at

retail display and what is sold at time of

purchase. We reserve the right to make

positive changes to our products at our

discretion.

Suggested Router Bit Speeds

Bit Diameter Max. Speed

1” (25mm) 24,000 RPM

1-1/4” - 2” (30-50mm) 18,000 RPM

2-1/4” - 2-1/2” (55-65mm) 16,000 RPM

3” - 3-1/2” (75-90mm) 12,000 RPM

61 Forest Plain Road

Orillia, Ontario, Canada

L3V 6H1

866-272-7492 Toll Free

705-726-8233 Local Phone

705-327-0295 Fax

Email: jessem@jessem.com

Website: www.jessem.com

IMPORTANT!

Read and understand the contents of

this manual before assembly or

operation of this product.

CONTENTS:

1-Rout-R-Lift

1-Height Adjustment Handle

Also includes 1-Insert Ring, 1-Insert Ring

Wrench, 1-1/8” Hex Wrench, 1-5/32” Hex

Wrench, 1-5/64” Hex Wrench, 1-Start Pin,

TOOLS REQUIRED FOR ASSEMBLY:

Screw Driver

7/16” Wrench

Summary of content (8 pages)

PAGE 1
Rout R Lift User Manual Model #02001 61 Forest Plain Road Orillia, Ontario, Canada L3V 6H1 866-272-7492 Toll Free 705-726-8233 Local Phone 705-327-0295 Fax Email: jessem@jessem.com Website: www.jessem.com Thank you for choosing this product from JessEm Tool Company. We appreciate your support and hope that our product serves you well. This product is designed to provide many years of reliable service provided it is used as intended and taken care of.
PAGE 2
IMPORTANT SAFETY PRECAUTIONS ! Before operating any router read and understand all safety instructions in the owner’s manual that came with the router. ! If you do not have a manual, contact the manufacturer and obtain one before using any power tool. ! Always wear eye protection in compliance with ANSI safety standards when operating any power tool. ! Always use proper guards and safety devices when operating power tools and machinery. ! Carefully check router bits before each use.
PAGE 3
ATTACH ROUTER TO THE MASTER RING (Cont’d) Using a felt tip marker or a pencil make a mark on the mounting plate for each hole that you will be using for your router. With the holes marked on the master ring, place the mounting plate on the base of your router and rotate it to line up the tapped holes in your router (Fig. 3). The countersunk holes and the engraving on the master ring should be facing upwards and with the engraved “T” to the top and the engraved “B” to the bottom.
PAGE 4
FIG. 8 TAB-LOC PHENOLIC INSERT RINGS Your Rout-R-Lift™ comes with one insert ring with a pre-drilled 1-1/2” diameter center hole. Additional ring sets are available with different diameter pre-drilled holes and/or no pre-drilled holes for creating your own custom centerhole diameters. 1. Place the insert ring into the centerhole of the Lift’s top plate (Fig. 8). 2.
PAGE 5
JESSEM TOOL LIMITED WARRANTY FIG. 9 RE-ADJUSTING THE THREAD TENSIONING All JessEm lifts feature our patented thread tensioning design. The design holds the position wherever you set the height. Thread tension is set at the factory and depending on the amount of use you may have to reset this adjustment periodically. 1. To adjust the thread tension, turn the Rout-R-Lift™ upside down on a table with the threaded height adjustment rod facing you (Fig 6). 2.
PAGE 6
HITACHI M12V HITACHI TR12 MAKITA 3612b, 3600 MAKITA 3612-C MAKITA 3621BR & C MILWAUKEE (OLD STYLE) PORTER CABLE 100, 536, 690, 691, 692, 693 MILWAUKEE PALM GRIP MAKITA 1101 SERIES PORTER CABLE 518, 520, 7518/19, 7538/39, 7529/7536 TRITON RYOBI 180 RYOBI RE-600 (NEW) RYOBI RE-600 (OLD) 500, 501 SEARS CRAFTSMAN (3 HOLE) SEARS CRAFTSMAN (4 HOLE) DEWALT 618 SEARS CRAFTSMAN (4 HOLE) MILWAUKEE 5625 BLACK & DECKER 7614-04 (TYPE 1) DEWALT 610, ELU 2721 6
PAGE 7
PARTS LIST FOR THE ROUT-R-LIFT™ Part # Description Size 1......F0001..........Flat Head Cap Screw .............................1/4" x 3/4" ...........................................28 2......P0001-1 ......Aluminum Main Plate ...........................14-3/4" x 11-3/4" x 3/16"......................1 3......E0042-1 ......Leveling Bar (Long)................................3/16 x 1/2" x 13-1/8".............................2 4......F0049 .........Flat Head Cap Screw .............................
PAGE 8
PARTS BREAKDOWN AND ASSEMBLY 1 37 38 39 2 36 35 3 34 4 5 6 31 7 32 30 33 8 9 10 11 29 28 12 27 13 14 15 24 23 22 21 26 16 25 20 17 18 19