Auto Feed Screwdriver MODEL 6832 Variable Speed I Reversing INSTRUCTION MANUAL Screw strip No load speed (RPM) Overall length Net weight 4 mm x 25 mm - 57 mm (5132" x 1" 2-114") 0 -- 2,800 372 mm (14-518") 2.0 kg (4.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
Total Length of Cord in Feet 0 - 25 26 - 50 Ampere Rating More Not More Than Than 0 6 10 12 - 6 10 12 16 51 - 100 101 - 150 A W G 18 18 16 14 16 16 16 12 16 14 14 12 14 12 Not Recommended 3
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified o n the nameplate of the tool. A power source w i t h voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source w i t h voltage less than the nameplate rating is harmful t o the motor. ADDITIONAL SAFETY RULES 1.
Adjusting the stopper plate (Fig. 1, 2, 3 & 4) There are two kinds of stopper plates; one is for screws 25 mm (1") - 41 mm (1-5/8") long and the other i s for screws 40 mm (1-9/16") - 57 mm (2-1/4") long. When the tool is shipped, the former stopper plate is installed on the casing and the latter stopper p l a t e on the feeder box. Replace the stopper plate as necessary. ~ Stopper plate for screws 25 mm (1 41 mm (1-5/8") Ion " Stopper for screws 40 mm (1-9/16") - 57 mm (2-1/4") long Fig. Pins Fig.
Adjust the stopper plate in accordance with the screw length as shown in Fig, 3 81 4. If necessary, loosen the bolts which secure the stopper plate. Fig. 3-1 : Fig. 3-2: Fig.3-3: Fig. 4-1 : Fig. 4-2 : Fig.
Setting the slide plate (Fig. 5 & 6) When driving screws 25 mm ( I " ) - 41 mm (1-5/8") long, set the slide plate to the position shown in Fig. 5. To set the slide plate, press it in the direction of the arrow while depressing the screw in the center of the adjusting knob. Z5mmll 1 41 m m l l 518 \ - Slide plate 4 Press \ Adjusting knob Screw lLzess Slide plate I Fig. When driving screws 40 mm (1-9/16") 57 mm (2-1/4") long, set the slide plate to the position shown in Fig. 6.
Installing the screw strip (Fig. 8 81 9) Insert the screw strip through the screw guide. Then insert it through the feeder box until the first screw reaches the position next to the driving position. Feeder box -Driving position Screw strip I Fig. Fig. 8 Removing the screw strip (Fig. IO) To remove the screw strip, just pull it out in the direction of the arrow. I / I Fig. 1( Carry hook (Fig. 11) The carry hook is convenient for hooking the tool to your belt.
Switch action (Fig. 12) CAUTION : Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. Switch t r i g g e k L o c y u t t o n Fig. 12 Continuous running (Fig.
Driving operation (Fig. 14) Switch on the tool by pressing the trigger and a t the same time pushing the lock button. Hold the tool squarely against the workpiece and apply forward pressure to the tool. The screw will be automatically carried to the driving position and driven into the workpiece. Fig. 14 IMP0 RTANT : Do not fire the tool without screws. This will damage the workpiece. 0 If the feeder box becomes sluggish in operation, spray car wax (spray type wax) on i t s sliding surfaces.
Extension handle (optional accessory) (Fig. 17) Use of extension handle allows you t o drive screws into floors while standing. Fig.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced a t the same time. Use only identical carbon brushes. lL Limit mark Fig. 18 Use a screwdriver to remove the brush holder caps.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. 0 Phillips bit 2-132 ( 5 per pkg.) Part No. A- 16536 0 Stopper plate (for screw 25 mm (1") 41 mm (1-5/8") long) Part No. 344054-0 0 Plastic carrying case Part No. 824421 -0 0 Hex wrench Part No.
Mar.-30-'95 US AUTO FEED SCREWDRIVER Model 6832 Note: The switch, noise suppressor and other part configurations may differ from country to country.
M O D E L 6832 ITEM NO. NO. USED Mar.-30-'95 $tD DESCRIPTION DESCRIPTION MACHINE ~ 1 2 3 4 5 6 7 8 9 10 I 1 12 13 14 15 16 17 18 19 20 21 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I 1 3 1 1 1 Slopper Base Box Cover Complete Leaf S p m g Slopper PI" 3 34 35 36 Feeder Box Complete Phillips Bit No 2 1 3 2 L COmpreSslOn Soring 21 Dust Cover Shifter Pin CaSlng C O m p k l e S18de Plate Leal spring Knob 4 0 compre.
P MAKITA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.