Instructions

16 ENGLISH
Speed adjusting dial
Therotationspeedofthetoolcanbechangedbyturn-
ingthespeedadjustingdial.Thetablebelowshows
the number on the dial and the corresponding rotation
speed.
►Fig.4: 1.Speedadjustingdial
Number Speed
1 10,000 min
-1
2 15,000 min
-1
3 20,000 min
-1
4 25,000 min
-1
5 30,000 min
-1
NOTICE: If the tool is operated continuously at
low speed for a long time, the motor will get over-
loaded, resulting in tool malfunction.
NOTICE: When changing the speed dial from "5"
to "1", turn the dial counterclockwise. Do not turn
the dial clockwise forcibly.
Electronic function
Thetoolisequippedwiththeelectronicfunctionsfor
easy operation.
• Constantspeedcontrol
Thespeedcontrolfunctionprovidestheconstant
rotationspeedregardlessofloadconditions.
• Softstart
Thesoft-startfunctionminimizesstart-upshock,
and makes the tool start smoothly.
Adjusting cutting depth
Toadjustthecuttingdepth,openthelocklever,then
movethetoolbaseupordownbyturningtheadjusting
screw.Aftertheadjustment,closethelockleverrmly.
►Fig.5: 1. Lock lever 2.Adjustingscrew
NOTICE: If the tool is not secured after closing
the lock lever, tighten the hex nut, and then close
the lock lever.
►Fig.6: 1.Hexnut
Adjusting cutting depth with the
plunge base
Optional accessory
1. Placethetoolontheatsurface.
2. Select the stopper screw by rotating the stopper
base.
►Fig.7: 1. Stopper screw 2. Stopper base
3. Loosenthestopperpolexingnut,thenpullupthe
stopperpolewhilepressingthefeedbutton.
►Fig.8: 1. Stopper pole 2.Fixingnut3. Feed button
4. Pushdownthetooluntilthetipofthetrimmerbit
touchestheatsurface,andthenturnthexingleverto
secure the tool.
►Fig.9: 1.Fixinglever2.Trimmerbit
5. Press down the stopper pole while pressing the
feedbuttonuntilitcontactsthestopperscrew.
►Fig.10: 1. Stopper pole 2. Stopper screw 3. Feed
button
6. Slide the depth pointer so that the pointer indi-
cates "0" on the scale.
►Fig.11: 1. Depth pointer
7. Adjustthecuttingdepthbypullingupthestopper
polewhilepressingthefeedbutton.
►Fig.12: 1. Stopper pole 2. Feed button
8. Toperformneadjustmentofthecuttingdepth,
turn the dial on the stopper pole so that it indicates "0".
►Fig.13: 1. Dial
9.
Turntheheadofthestopperpoletoobtainthedesired
depth.Toincreasethedepth,turntheheadcounterclock-
wise.Todecreasethedepth,turntheheadclockwise.
►Fig.14: 1.Headofthestopperpole
10. Tightenthestopperpolexingnut.
►Fig.15: 1.Fixingnut
11. Releasethexinglever.
►Fig.16: 1.Fixinglever
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing trimmer bit
NOTICE: Do not tighten the collet nut without
inserting the bit.Thecolletconemaybreak.
Insertthetrimmerbitallthewayintothecolletcone.Press
theshaftlockandtightenthecolletnutwiththewrenchor
tightenthecolletnutsecurelywiththetwowrenches.To
removethebit,followtheinstallationprocedureinreverse.
►Fig.17: 1.Shaftlock2. Loosen 3.Tighten
4. Wrench 5. Collet nut
►Fig.18: 1. Wrench 2. Loosen 3.Tighten4. Collet nut
NOTE:Theshaftlockmaynotreturntotheoriginal
position when you tighten the collet nut at the instal-
lationofthetrimmerbit.Theshaftlockreturnstothe
original position when you start the tool.
►Fig.19: 1.Shaftlock
Installing or removing the trimmer
base
1. Openthelockleverofthetrimmerbase,then
insert the tool into the trimmer base aligning the groove
on the tool with the protrusion on the trimmer base.
►Fig.20: 1. Lock lever
2. Close the lock lever.
3. Attachthedustnozzletothetrimmerbase,and
then tighten the thumb screw.