Instructions
17 ENGLISH
►Fig.21: 1.Dustnozzle2.Thumbscrew
►Fig.22
Toremovethebase,followtheinstallationprocedure
in reverse.
CAUTION: When using the tool with the trim-
mer base, be sure to install the dust nozzle on the
trimmer base.
Installing or removing the tilt base
Optional accessory
1. Openthelockleverofthetiltbase,theninsertthe
tool into the tilt base aligning the groove on the tool with
the protrusion on the tilt base.
►Fig.23: 1. Lock lever
2. Close the lock lever.
Toremovethebase,followtheinstallationprocedure
in reverse.
Installing or removing the offset
base
Optional accessory
1. Presstheshaftlock,thenloosenthecolletnut.
►Fig.24: 1. Collet nut 2.Shaftlock3. Wrench
2. Remove the collet nut and the collet cone.
►Fig.25: 1. Collet nut 2. Collet cone
3. Installthepulleyonthetoolbypressingtheshaft
lock and tightening the pulley with the wrench.
►Fig.26: 1. Wrench 2. Pulley 3.Shaftlock
4. Loosen the screws on the base plate, and then
remove the base plate.
►Fig.27: 1. Base plate
5. Openthelockleveroftheoffsetbase,theninsert
thetoolintotheoffsetbase.
►Fig.28: 1. Lock lever
6. Mount the belt to the pulley by rotating the belt
manually.
►Fig.29: 1. Pulley 2. Belt
7. Close the lock lever.
►Fig.30: 1. Lock lever
8. Attachthebaseplatebytighteningthescrews.
►Fig.31: 1. Base plate
9. Insertthecolletconeandthetrimmerbitintothe
offsetbase,andthentightenthecolletnut.
►Fig.32: 1.Trimmerbit2. Collet nut 3. Collet cone
10. Insertthehexwrenchintotheholeoftheoffset
base, and then tighten the collet nut with the wrench.
►Fig.33: 1. Collet nut 2. Wrench 3.Hexwrench
Toremovethebase,followtheinstallationprocedure
in reverse.
NOTE: You can also mount the belt to the pulley with-
outremovingthebaseplateasshowninthegure.
►Fig.34: 1. Pulley 2. Belt
Installing or removing the plunge
base
Optional accessory
1. Openthelockleveroftheplungebase,theninsert
the tool into the plunge base all the way aligning the
groove on the tool with the protrusion on the plunge
base.
►Fig.35: 1. Lock lever
2. Close the lock lever.
Toremovethebase,followtheinstallationprocedure
in reverse.
Installing or removing the parallel
ruler on the plunge base
Optional accessory
Inserttheguidebarsintotheholesintheplungebase,
andthentightenthewingbolts.Toremovetheruler,
followtheinstallationprocedureinreverse.
►Fig.36: 1. Wing bolt 2. Guide bar
Installing or removing the dust
nozzle on the plunge base
Insertthedustnozzleintotheplungebasesothatthe
protrusiononthedustnozzletsinthenotchinthe
plunge base, and then tighten the thumb screw on the
dustnozzle.Toremovethenozzle,followtheinstalla-
tion procedure in reverse.
►Fig.37: 1. Protrusion 2.Dustnozzle3.Thumb
screw
►Fig.38
OPERATION
Using the tool with the trimmer base
Set the tool base on the workpiece without the trimmer bit
makinganycontact.Turnthetoolonandwaituntilthebit
attainsfullspeed.Movethetoolforwardovertheworkpiece
surface.Keepthetoolbaseushwhilemovingthetool.
When cutting the edge, be sure to keep the workpiece
surfaceontheleftsideofthetrimmerbitinthefeed
direction.
►Fig.39
NOTE:Beforecuttingontheactualworkpiece,itis
recommendedtomakeasamplecut.Theproperfeed
speeddependsonthetrimmerbitsize,thekindof
workpiece,anddepthofcut.Movingthetoolforward
toofastmaycauseapoorqualityofcut,ordamage
tothebitormotor.Movingthetoolforwardtooslowly
mayburnandmarthecuttingsurface.
When using the trimmer shoe, the straight guide, or the
trimmer guide, be sure to keep it on the right side in the
feeddirection.Thiswillhelptokeepitushwiththeside
oftheworkpiece.
►Fig.40: 1.Trimmerbit2. Workpiece 3. Straight
guide