Instructions
19 ENGLISH
Using the tool with the offset base
Theoffsetbaseisconvenientforworkinatightarea
such as a corner.
►Fig.58
Using the trimmer base with the
offset base plate and grip
Theoffsetbaseplatecanalsobeusedwithatrimmer
baseandagripattachment(optionalaccessory)for
more stability.
1. Loosen the screws on the base plate, then remove
thebaseplatefromtheoffsetbase.
►Fig.59: 1.Offsetbaseplate2.Trimmerbaseplate
2. Attachtheoffsetbaseplatetothetrimmerbaseby
tightening the screws.
3. Attachthegripattachmentandthebartypegripto
theoffsetbaseplatebytighteningthescrews.
►Fig.60: 1. Bar type grip 2. Grip attachment
Theknobtypegripremovedfromtheplungebasecan
beinstalledontheoffsetbaseinsteadofthebartype
grip.
►Fig.61: 1. Screw 2.Knobtypegrip
Using the tool with the plunge base
Alwaysholdthegripsrmlywithbothhandsduring
operation. Operate the tool in the same way as the
trimmer base.
Using the straight guide
Optional accessory
1. Installthestraightguidetotheguideholderby
tighteningthewingnut.Inserttheguideholderintothe
holes in the plunge base, and then tighten the wing
bolts.
►Fig.62: 1. Wing bolt 2. Guide holder 3. Wing nut
4. Straight guide
2. Loosen the wing nut on the straight guide and
adjustthedistancebetweenthebitandthestraight
guide.Atthedesireddistance,tightenthewingnut.
►Fig.63: 1. Wing nut
3. Operate the tool in the same way as the straight
guideforthetrimmerbase.
►Fig.64
Using the templet guide
Optional accessory
1. Loosen the screws on the base and remove them.
Place the templet guide on the base, and then tighten
the screws.
►Fig.65: 1. Screw 2.Templetguide
2. Operate the tool in the same way as the templet
guideforthetrimmerbase.
►Fig.66
Using the parallel ruler
Theparallelruleriseffectivelyusedforstraightcuts
whenchamferingorgrooving.Adjustthedistance
betweenthebitandtheparallelruler.Atthedesired
distance, tighten the wing bolts to secure the parallel
ruler. When cutting, move the tool with the parallel ruler
ushwiththesideoftheworkpiece.
►Fig.67
Ifthedistance(A)betweenthesideoftheworkpiece
andthecuttingpositionistoowidefortheparallelruler,
orifthesideoftheworkpieceisnotstraight,theparallel
ruler cannot be used.
Inthiscase,rmlyclampastraightboardtothework-
piece and use it as a guide against the plunge base.
Feedthetoolinthedirectionofthearrow.
►Fig.68
Changing knob type grip to bar type
grip
Toinstallthebartypegripontheplungebase,loosen
thescrewoftheknobtypegrip,thenremovetheknob
type grip, and then install the bar type grip by tightening
it.
►Fig.69: 1.Knobtypegrip2. Screw 3. Bar type grip
MAINTENANCE
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
TomaintainproductSAFETYandRELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual.Theuseofanyother
accessoriesorattachmentsmightpresentariskof
injurytopersons.Onlyuseaccessoryorattachment
foritsstatedpurpose.
Ifyouneedanyassistanceformoredetailsregard-
ing these accessories, ask your local Makita Service
Center.
• Straightandgrooveformingbits
• Edgeformingbits
• Laminatetrimmingbits