Digital Satellite Receiver PLAZA MODELS ST 100 / ST 120 ST 200 / ST 300 PLAZA MODELS ST 100 / ST 120 ST 200 / ST 300 Instruction Manual (English) http://www.plaza-st.
CONTENTS INTRODUCTION .....................................................................................................................................2 FEATURES .............................................................................................................................................3 CONNECTORS AND DEFINITIONS ............................................................................................................4 FRONT PANEL CONNECTORS ...........................................
FEATURES FEATURES 1 LNB input, IF signal loop through, supports Universal, Single, C Band and Wide Band LNB Multiple LNB switching 0/12V, 14/18 volts, 22KHz and DiSEqC 1.2 2 SCART, TV (CVBS / RGB) and VCR/DVD with loop through facility S-Video output on mini DIN.
REAR PANEL CONNECTIONS CONNECTORS AND DEFINITIONS Please do not connect the power to the receiver until all other connections have been made and checked. R1: AC IN (Power Cord) Connect this lead to the mains outlet (100-240 V AC 50/60 Hz) R2: LNB IN (IF Input) Connect the IF cable from your LNB to this connector. R3: LOOP OUT If you have a second satellite receiver, connect the receivers LNB input to this connector. R4: ANT IN Connect your UHF TV antenna to this connector.
F13: IRDETO CARD SLOT (For Models with embedded Irdeto) Insert your smart card into this slot. REMOTE CONTROL FUNCTIONS We recommend that you familiarize yourself with the remote control handset prior to installing the receiver. OPERATION IN PROGRAMMING MODE The menus are designed to assist you from the moment you switch on the receiver. Follow the help messages at the bottom of the menu. INSTALLATION For digital quality picture, connect the receiver to your TV using a fully wired SCART lead.
TV Settings TV Standard: Select the output for your TV. Example: for UK select PAL I. If your TV supports ‘Auto Sensing’ then select Auto. Screen Format: Select the picture aspect ratio for your TV. Video Output: Select signal output for your TV. If the teletext function on your TV does not work when viewing channels from other sources such as terrestrial TV, select COMP mode. UHF Channel: Select a UHF channel between 21 – 69. STORE: After above settings move to store and press OK key.
EXAMPLE: To configure four LNB EXAMPLE: To configure MONOBLOCK LNB Astra 1(19.2E), select LNB No 1 and set DiSEqC to Mini-A Astra 2 (28.2E), select LNB No 1 and set DiSEqC to 1 Hotbird 1-6(13E), select LNB No 2 and set DiSEqC to Mini-B Astra 1 (19.
Search Mode: Select search option for each satellite. See below for options. Options with + D will also include data channels Auto All - All TP, Video and Radio channels. Auto All + D -All TP, Video, Radio and Data channels. Auto FTA - All TP for Free To Air Video and Radio channels. NIT All – All TP, Video and Radio channels with Network Identification Table. NIT All + D – All TP, Video, Radio and Data channels with Network Identification Table.
Set Multisat Search 2, LNB No 2 and select horizontal TP from low band. Adjust skew (externally) to - value for maximum signal and quality. Set Multisat Search 3, LNB No 3 and select vertical TP from high band. Adjust skew (externally) to + value for maximum signal and quality. Set Multisat Search 4, LNB No 4 and select horizontal TP from high band. Adjust skew (externally) to - value for maximum signal and quality. Finally press OK key on Start.
SATELLITE LIST Press SAT key and the combined channel and satellite list will appear. Select a channel from this list and exit. TO SELECT A CHANNEL FROM ANOTHER SATELLITE Use CH and PAGE up / down to scroll through the satellite list Press OK on required satellite, the channel list will change and the cursor will also move to channel list. Use CH and PAGE up / down to scroll through the channel list Press OK on required channel. The antenna positioner will automatically move to that satellite.
This menu is pre-configured and ready to upgrade. Select Start and press OK. If you have a motorized antenna, it will automatically move to Hot Bird 1-6 (13.0E). This may change to a different satellite in future. In this case follow as below Satellite: Select the satellite providing the OTA Upgrade. LNB No: Select number. Freq: Enter the TP frequency using 0-9 keys Polarity: Select polarity S / R: Enter symbol rate using 0-9 keys Load PID: Enter the PID for the channel using 0-9 keys.
ELECTRONIC PROGRAM GUIDE (EPG) To display correct EPG it is important to set the time first. To display EPG, what’s on now and next, press EPG (red) key. Channel No. Select channel and press OK Highlighted Event. Press OK for details and PAGE up / down for next page. NOTE: If there is no EPG transmitted, it will state ‘ No Data’. After changing channel please allow few seconds before you press EPG key. INSTALLING FAVORITE CHANNELS There are 11 TV and 11 Radio channel lists you can create.
group and this will highlight these in red. When finished, press EXIT. Then store the settings. TO RENAME CHANNEL Select Rename and press OK. Select channel and press OK, a keypad will appear. Select character and press OK. After naming press EXIT. Then store the settings. TO MOVE CHANNEL Select Move and press OK. To move individual channel, press OK twice on the channel. This will highlight it in mauve. Then select a position in the list and press OK.
4. When finished the slave receiver will reboot and come up with a channel. TROUBLE SHOOTING GUIDE If you suspect there is a problem with your receiver, please check the following trouble shooting guide before calling a Manhattan authorised service agent. WARNING! Do NOT attempt to repair the receiver yourself. Tampering with the receiver may result in fatal electric shock and will invalidate your warranty.
RF MODULATOR Frequency Channel Range TV standard 470MHz to 860 MHz UHF CH21 to 69 PAL BG/ I /K PAL M, NTSC M POWER SUPPLY Input Voltage Type Power Consumption Protection 100 -- 240 V AC, 50/60Hz ~ SMPS Max 30W Separate Internal Fuse PHYSICAL DIMENSIONS Size (W X H X D) 300 X 67 X 240 mm Eurosat® and Manhattan® are registered trademarks of Eurosat Distribution Ltd. Eurosat reserves the right to alter product specifications without prior notice.
