Use and Care Manual

13Contact us at www.mantis.com
Cordless Tiller/Cultivator Operation
The wheels can be adjusted in 3 different positions. Always ensure the wheels are securely locked!
Do not attempt to use the tiller/cultivator with the wheels in any other position or unlocked!
INTENDED USE
This tiller/cultivator is intended for loosening and working up the soil in a garden and
for tilling coarse soil for mixing in fertilizer, peat and compost in planting areas. This
tiller/cultivator should not be used to till extremely dry or wet soil.
This tiller/cultivator should not be used in rain or humid environments.
For safety reasons it is essential to read the entire instruction manual before rst
operation and to observe all the instructions.
This tiller/cultivator is intended for private household use only, not for any commercial
trade use. It must not be used for any purposes other than those described.
TWO SPEEDS SWITCH
This product features a switch that allows operation
at one of two, preset speeds. The switch is located
on the back of the motor facing the operator. When
set on low speed (I) the digging tines will move
more slowly and deliberately than when set on
high speed (II). Select speed levels based upon
preference relating to job requirements. The speed
switch should only be engaged when the tiller/
cultivator is turned off and in a stationary position.
1. Insert fully charged power battery in the tiller/cultivator.
2. Press the lock-off button and hold it in position (Figure 1, step 1).
3. Squeeze the ON/OFF switch to turn the tiller/cultivator “ON” (Figure 1,
step 2), release the lock-off button afterwards.
3. Release the ON/OFF switch to turn the tiller/cultivator “OFF” in order
to stop it.
The wheels can be adjusted to 3 positions. Lower the wheel height for shallow soil
penetration. Raise the wheel height for deeper soil penetration.
Adjust the wheels when the tiller/cultivator is off, wait for moving parts to stop and
remove the battery. Tilt the tiller/cultivator forward to rest on the motor housing. Grasp
the wheel assembly by the axel and pull toward you. Move the assembly up or down
(as needed) and allow the pins on the assembly to slot into one of the three pre-set
positions.
WHEEL ADJUSTMENT
STARTING AND STOPPING TILLER/CULTIVATOR
19
Wheel adjustment
WARNING!
Always switch the product off and disconnect it from power
supply before making any adjustments!
The wheels can be adjusted to 3 positions.
1. Pull on the wheel and move it to required position, let go of the wheel and
make sure it locks in position (Figs. 6-8).
WARNING! The wheels can be adjusted in 3 different positions.
Always ensure the wheelsare securely locked! Do not attempt
to use the product with the wheels in any other position or
unlocked!
Switching on/off
1. Press the lock-off button and hold it in position (Fig. 9, step 1).
2. Squeeze the on/off switch to switch the product on (Fig. 9, step 2), release
the lock-off button afterwards.
3. Release the on/off switch to switch the product off.
19
Wheel adjustment
WARNING!
Always switch the product off and disconnect it from power
supply before making any adjustments!
The wheels can be adjusted to 3 positions.
1. Pull on the wheel and move it to required position, let go of the wheel and
make sure it locks in position (Figs. 6-8).
WARNING! The wheels can be adjusted in 3 different positions.
Always ensure the wheelsare securely locked! Do not attempt
to use the product with the wheels in any other position or
unlocked!
Switching on/off
1. Press the lock-off button and hold it in position (Fig. 9, step 1).
2. Squeeze the on/off switch to switch the product on (Fig. 9, step 2), release
the lock-off button afterwards.
3. Release the on/off switch to switch the product off.
19
Wheel adjustment
WARNING!
Always switch the product off and disconnect it from power
supply before making any adjustments!
The wheels can be adjusted to 3 positions.
1. Pull on the wheel and move it to required position, let go of the wheel and
make sure it locks in position (Figs. 6-8).
WARNING! The wheels can be adjusted in 3 different positions.
Always ensure the wheelsare securely locked! Do not attempt
to use the product with the wheels in any other position or
unlocked!
Switching on/off
1. Press the lock-off button and hold it in position (Fig. 9, step 1).
2. Squeeze the on/off switch to switch the product on (Fig. 9, step 2), release
the lock-off button afterwards.
3. Release the on/off switch to switch the product off.
Transport position Work position (low) Work position (high)
Figure 1
Always switch the product off
and wait for moving parts to
stop. Remove the battery before
making any adjustments!
Step 1
Step 2