Owner's Manual

26
N
0
5805 / N
0
5802 INTEGRATED AMPLIFIER / OWNER’S MANUAL
Config: This menu group allows you to lock, restore, import, or
export Setup configuration settings.
Config Export: Press Enter to export all setup configuration
information to a thumb drive inserted in the rear panel
USB port. This data can then be used to configure other
N
0
5805 / N
0
5802 units or serve as a backup so you can
quickly reconfigure your unit. Once you have your unit’s
configuration precisely as you would like it, we strongly
recommend you save a Config Export file to a thumb drive in
case an untoward event erases your configuration settings.
Config Import: Press Enter to import all setup configuration
information from a thumb drive inserted in the rear-panel
USB port.
Config Lock: Engage the Lock to prevent accidentally changing
the Setup parameters. The factory default setting is Off.
Config Restore: Restores all N
0
5805 / N
0
5802 parameters to
their factory-default conditions.
Network: This menu offers access to the following network-
related parameters. They are useful only if you want to connect
your unit to a network to access controls and setup functions
via PC or tablet.
Name: Displays your N
0
5805’s network name in this format
N5805XXXX (the X’s represent the last four characters of the
unit’s unique MAC address). Use the input select control to
select the character you want to change, and the volume
control to scroll through available characters.
Current Gateway: Displays the Gateway IP address. This
setting is informational only and does not provide any user
adjustments.
DHCP: Lets you toggle DHCP mode (network auto-
configuration) On or Off. The factory default behavior is
On. When the mode is set to Off, you can specify static IP
and Subnet addresses for your N
0
5805 / N
0
5802. Selecting
Renew (available only when DHCP is set to On) refreshes
your DHCP configuration, assigning a new IP address to
your N
0
5805 / N
0
5802. This function is often useful when
troubleshooting a network connection.
Current IP: Shows the IP address currently assigned at the
factory (or by DHCP or manually) to your N
0
5805 / N
0
5802.
Enter this number in the address (URL) line of a browser
connected to the Internet. (This setting is informational only
and does not provide any user adjustments.)
Current Subnet: Shows the subnet address currently
assigned (by DHCP or manually) to your N
0
5805 / N
0
5802.
(This setting is informational only and does not provide any
user adjustments.)
Trigger: This setting configures the 12V trigger. NOTE: Using a
trigger input overrides the
Standby button.
Mode: These choices determine how the 12V trigger signals
are sent and received.
Normal: The default setting, appropriate for most other
components.
Pulsed: Some products (such as some older Mark
Levinson components) require a pulsed trigger signal.
Theater: Turns on the N
0
5805 and automatically selects
the input configured for SSP mode.
Off: Disables the Trigger In/Out connections.
Delay: This setting determines the amount of time after
fully exiting the
Standby mode that the unit waits to pass
a trigger signal to the trigger output jack. The choices are
0 - 10 seconds, with 0 being the default. NOTE: as it can
take a few seconds for the N
0
5805 / N
0
5802 to enter and exit
Standby mode, the net trigger delay time will be longer than
the value you select.
Front IR: This menu allows you to turn the N
0
5805 / N
0
5802’s
front IR receiver on or off. If you plan to use the rear-panel
IR input, you must set the front IR receiver to Off. If you use a
3rd party control via IP or RS232, and do not plan to use IR for
control, we recommend you turn the IR control to Off.
Amplifier Enable: Selecting Off turns off the amplifier section
of the unit so that it will operate solely as a preamplifier or
headphone amplifier. The default value is On.
SETUPSETUP