v. 14.march.
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions; 2) Keep these instructions; 3) Heed all warnings; 4) Follow all instructions; 5) Do not use this apparatus near water; 6) Clean only with dry cloth; 7) Do not block any ventilation openings.
MARKBASS EVO 1 A WORD FROM MARCO DE VIRGILIIS Thank you for choosing the Markbass EVO1 head. It’s the result of the mix between classic and advanced technology evolution to allow bassists to have not only just a ‘gorgeous’ bass sound, but always the ‘right’ sound... no matter which genres and techniques you’re playing!!! The MARKBASS EVO 1 offers six AMPS tone choices for each of the two channels, clean and distorted.
FRONT PANEL 1) INPUT 1 2) CH1/CH2/MIX 3) AMP 1 4) GAIN This knob sets the gain level of the channel 1. 5) LOW This knob controls the amount of low frequencies of the selected AMP / CH1. 6) MID The Mid control regulates the midrange frequencies of the selected AMP / CH1. 7) HIGH The High knob controls the amount of high frequencies of the selected AMP / CH1. 8) LEVEL Controls the level of the selected AMP model on CH1.
12) AMP 2 Select between six AMPS tone choices available at channel 2.
REAR PANEL • The MIDI RX CHANNEL is setted on #0 The switch between channel and mix are setted as for the PROGRAM CHANGE: 10 11 AUX Make sure the2 unit is grounded; all threeLOW terminals of theMID AC AMP GAIN 4 5 power3plug must be connected to avoid any injury to the user or 6 damage to the unit. CH2 2 The Markbass EVO 1 is manufactured to be used in the country 1 it has been sold, and it’s factory preset to that country’s where voltage.
32/34) SEND/ RETURN 1 If you use effect pedals or rack gear, you can route them through the CH1 using SEND 1 (32) and RETURN 1 (34), connecting the SEND to the input of the effect and the RETURN to the effect’s output using instrument cables. 33/35) SEND/ RETURN 2 If you use effect pedals or rack gear, you can route them through the CH2 using SEND 2 (33) and RETURN 2 (35), connecting the SEND to the input of the effect and the RETURN to the effect’s output using instrument cables.
TECHNICAL SPECS OTHER CHANNELS: Two + MIX mode INPUT CH1: 1x 1/4” mono jack (impedance 1MΩ) INPUT CH2: 1x 1/4” mono jack (impedance 1MΩ) AUX IN: 1x 1/8” stereo jack USB port: USB type B 2 RETURN INPUTS: 2x 1/4” mono jack (50KΩ) 2 SEND OUTPUTS: 2x 1/4” mono jack (1KΩ) SPEAKER OUTPUTS: 2x 1/4” mono jack + 1x Speakon parallel wiring, minimum impedance load 4 ohms LINE OUT 1: 1x XLR male balanced LINE OUT 2: 1x XLR male balanced PHONES OUTPUT: 1x 1/8” stereo jack MIDI IN: DIN 5 poles HEIGH
NOTE EVO1 CONTROLLER MARKBASS CONTROL SOFTWARE The optional Markbass EVO CONTROLLER allows to active CH1 / CH2 or MIX both, turn ON/OFF the FX1, FX2 and BOOST, plus accessing the TUNER with MUTE function pressing and holding the boost switch. The Markbass EVO Control software is available for FREE DOWNLOAD at www.markbass.
Product specifications are subject to change without notice Italy - 66020 San Giovanni Teatino (Ch) - Via Po, 52 - Tel. +39 085 446 3755 - Fax +39 085 440 7764 www.markbass.it - info@markbass.