Instructions / Assembly

ManualsBrandsMartha Stewart Living ManualsHome Decor9 ft. Pre-Lit LED Blue Noble Spruce Artificial Christmas Tree with Warm White Lights

NOTE: This product employs overload protection (fuse). A

blown fuse indicates an overload or short-circuit situation. If

the fuse blows, unplug the product from the outlet. Also

unplug any additional strings or products that may be

attached to the product. Replace the fuse as per the user

servicing instructions (follow product marking for proper fuse

rating) and check the product. If the replacement fuse blows,

a short-circuit may be present and the product should be

discarded.

13. The bottom section of your tree contains an extension

cord with an ON/OFF foot pedal. Remove the twist tie

from the cord and plug into a working wall outlet. Press

once to activate; press again to deactivate (Fig 7).

9. Align the flat ends of both connectors as shown and

connect them together. Slide the screw cover from the

“male” connector over the “female” connector and

tighten (Fig 5).

Fig 7

Fig 4

Fig 5

This pre-lit tree includes extra bulbs for any replacements that you

may need to perform on your tree. If extra parts are needed,

contact the Customer Service Team at 1-877-527-0313.

MAINTENANCE

Made in China

Printed in China

This is not a toy, for decorative use only.

a) Before changing fuse, make sure the set is unplugged.

b) Grasp plug and remove from the

receptacle or other outlet device.

Do not unplug by pulling on cord.

c) Using a flathead screwdriver, open fuse cover. Slide open the

fuse access cover on top of attachment plug towards blades.

d) Remove fuse carefully.

e) Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse

(provided with product) inside of plug.

f) Close fuse cover. Slide closed the fuse access cover on top of

attachment plug. Make sure door is fully closed and the fuse

is completely covered.

g) Risk of fire. Do not replace attachment plug. Contains a safety

device (fuse) that should not be removed. Discard product if

the attachment plug is damaged.

CCT14

Model No. 7208006-51 / 7208007-51

3. Lift each section straight up as you remove it from the section

below. Gently fold the branches up toward the center and place in

storage container.

4. To remove the bottom and final section; loosen the eyebolts by

turning in a counter-clockwise direction and lift section “A” from the

support collar of the tree stand.

5. Gently fold the branches of each section upward, towards the

center, and position in the storage container.

NOTE: With the exception of the tree’s “top” section; by holding

each section upside down; the branches will collapse downward,

due to the hinging, aiding in the packing of each section into the

storage container.

6. Fully unthread the eyebolts from the tree’s stand and fold together;

placing in the storage container.

7. It is recommended to always store the tree in a cool, dry location

protected from excessive exposure to heat or sunlight.

1. Gently remove the plug from its electrical outlet, and carefully bind

the cord which contains the on/off push button foot pedal and plug.

2. To disconnect the sections, locate the connection-labeled light

strings, unscrew the cap, and gently pull apart the light strings.

There will be two or three connections depending on the size of

your tree (Fig 6).

NOTE: It is not necessary to disconnect any light strings other than

the ones with the numerical connection labels.

CARE AND CLEANING

1. If the tree does not illuminate, press the ON/OFF foot pedal. It may

be in the OFF position.

2. Unplug the tree and check all coaxial connections as shown in

Figure 5. The light sets are connected to the ON/OFF foot pedal

extension cord through a converter plug (Fig 8). Be sure to check

both the coaxial connections and the connection to the ON/OFF

foot pedal extension cord.

3. If the tree is still not illuminated, unplug the tree and check the

fused plug on the ON/OFF foot pedal extension cord for a missing

or burned out (open) fuse. A replacement fuse is located in the

plug cavity. If additional fuses are needed, use only 5A 125V fuses.

4. If one section of the tree does not illuminate, check the coaxial

connections in that section.

TROUBLESHOOTING

NOTE: DO NOT USE A DIMMER SWITCH OR INSTALL ANY

ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS

DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL INJURY.

THIS ACTION WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF

THIS PRODUCT.

Fig 8

WARRANTY INFORMATION

If for any reason, after assembly, the tree does not light please call

our toll free number 1-877-527-0313.

The limited warranty of this tree applies only to the original

purchaser against manufacturer defects. A valid sales receipt must

be retained as proof of purchase. This product was pre-tested before

shipment and date coded.

The warranty of this pre-lit tree is void when the product is used for

commercial purposes.

Warranty on Lights:

For up to 5 years from the date of purchase, Home Depot will replace

free of charge any manufacturer defect found to the lighted portion

of your tree.

Warranty on Tree:

For up to 5 years from the date of purchase, Home Depot will replace

free of charge any manufacturer defect found to the tree.

Note: After your pre-lit tree is assembled, please check your tree for

any loose or damaged bulbs. Loose or damaged bulbs must be

replaced promptly in order to maintain the performance and life

expectancy of your pre-lit tree. If a bulb burns out, please replace it

at once (see replacement instructions). Failure to replace a burned

out bulb will result in a shorter life span for the remaining bulbs.

Failure to replace burned out bulbs, or misuse of this product will

void the warranty. This Christmas tree is a seasonal product. It is

intended for indoor use only and for temporary (90 days max)

installation and use only. Keep away from heat and moisture.

DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455

Carefully unpack all tree components from the carton

(Fig 1). Your tree should include the following:

1 Folding metal tree stand with 3 eyebolts

1 ON/OFF foot pedal extension cord which is already

connected to the tree

1 Bag of replacement bulbs included with these

instructions

Tree sections as noted below:

7.5’ tree – 3 sections

9’ tree – 4 sections

PRE-ASSEMBLY

Packaging Contents

4. Carefully cut the nylon strapping bounding the branches

upright. CAUTION: Be extremely careful not to cut any of the

expose light set wires.

5. Now gently guide the branches downward into place.

6. Locate the next section of the tree identified by a label

marked “B.”

7. Remove the protective plastic cap from the end of the pole

and insert that end into the pole from section “A” until it is

fully seated.

8. To electrically connect the sections, locate the coaxial

connectors labeled “1.” There will be one connector in

section “A” and one in section “B” of your tree (Fig 4).

Note: Do not remove the connector labels, as they will help

you disassemble and reassemble the tree in the future.

Connection 2

Connection 1

Foot Pedal

Fig 6

10. Carefully cut the nylon strap holding the branches together.

CAUTION: Be sure not to cut any of the light set wires.

11. Gently guide the branches downward into place.

12. Depending on the height of the tree you have purchased,

you will continue to build your tree upward section by

section in this fashion until it is completed. The section

labels are in alphabetical order from the bottom to the top

of your tree (Fig 6).

Fig 2

ASSEMBLY OF THE TREE

1. Locate the bottom section of the tree which is identified by

a label on the outer branches marked “A” (Fig 6).

2. Remove the protective plastic cap from the end of the

pole, (that is pinched to a point), and place that end into

the tree stand. Be sure that the pointed end of the pole

extends to the bottom of the stand.

3. Now tighten the eyebolts evenly on the tree stand; being

careful not to over-tighten (Fig 3).

Fig 3

NOTE: ALTHOUGH THE LED LIGHT STRINGS ON THE TREE ARE RATED

FOR INDOOR OR OUTDOOR USE; THE COMBINATION OF THE TREE

WITH THE LED LIGHTS IS RECOMMENDED FOR INDOOR USE ONLY.

Fig 1

ASSEMBLY OF THE TREE STAND

1. Remove the tree stand from the plastic bag, loosen the eye

bolt and open the tree stand to form an “X”.

2. Align the holes for the insertion of the remaining (2) eyebolts.

3. Insert each eyebolt and begin threading in a clockwise

direction for a couple of rotations only; leaving enough room

for the tree’s pole from section “A” to be inserted into the

assembled stand (Fig 2).

4. Place the tree stand in its desired location; as once the tree is

fully assembled, it may be too difficult to move and relocate.

15”

2014 Home Depot MSL

Blue Noble - Tree Instruction Sheet (English)

Date: 3/13/14

11.5”

7208006-51 (7.5 ft Blue Noble)

7208007-51 (9 ft Blue Noble)

Summary of content (2 pages)

PAGE 1
2014 Home Depot MSL Blue Noble - Tree Instruction Sheet (English) Date: 3/13/14 7208006-51 (7.5 ft Blue Noble) 7208007-51 (9 ft Blue Noble) 15” CCT14 Fig 6 Fig 3 C Model No. 7208006-51 / 7208007-51 2 Connection 2 2 PRE-ASSEMBLY Packaging Contents Carefully unpack all tree components from the carton (Fig 1).
PAGE 2
014 Home Depot MSL Blue Noble - Tree Instruction Sheet (Spanish) Date: 3/19/14 7208006-51 (7.5 ft Blue Noble) 7208007-51 (9 ft Blue Noble) 15” CCT14 Fig 6 Fig 3 C 2 Modelo N° 7208006-51 / 7208007-51 PREENSAMBLAJE Contenido del embalaje Desembale cuidadosamente todos los componentes del árbol de la caja (Fig 1).