Instructions / Assembly

Bulb Replacement Instructions
National Tree Company 2 Commerce Drive, Cranford, New Jersey 07016 USA www.nationaltree.com
Shaping the tree branches is the last
step of assembly. The care and
attention given to this final process will
result in a genuinely beautiful and
appealing holiday centerpiece.
1. Every tree style is shipped from the
factory with the tips of each branch
compressed to the center (Figure 1).
2. Each branch tip must be shaped to
it’s proper position to give the tree a
natural look. This is done by gently
grasping the left and right wing tips
and spreading them out away from
the center tip (Figure 2).
3. Each individual tip should then be
spread out separately. Tips should
then be bent slightly upward to add a
more natural looking appearance.
Figure 3 shows a typical tree branch
after shaping.
4. As you shape closer to the top, the
branches will not have wing tips, but
will otherwise shape in the same
manner as lower sections.
Memory Shape
®
Trees
Trees that feature Memory Shape tip technology do not require
branch shaping. Tree branches are pre-shaped during manufac-
ture and spring into shape upon assembly.
Trees with Music Match
®
Bluetooth
®
Light System
OPERATING INSTRUCTIONS
1. Turn on power to the Music Match unit by pressing the ON/OFF
button on the front panel.
2. Navigate to the Bluetooth screen of your Bluetooth enabled phone,
tablet or computer and select the option to search for devices.
3. A device called “Christmas Tree” will appear; select this to connect
your Bluetooth device to the Music Match unit. Your device will
indicate that “Christmas Tree” is connected and the Music Match
unit will announce the word ‘Connected’.
4. At this point, you can open any music program on your device and
play a song. The music will stream through the speaker of the
Music Match unit and the lights on the tree will ‘dance’ in sync with
the music playing.
Removing the Music Match device for normal light operation:
disconnect the device cord from the tree light string cord, then
disconnect the transformer. Connect the transformer to the tree
light string cord.
Shaping Instructions
1. Unplug light string from power source.
2. Pull up on the Bulb Lock unlatching
the bulb from the bulb socket. Gently
pull the bulb straight out (Figure 1).
3. Before inserting the new
bulb into socket, make sure
that the two wires on either
side of the the bulb base
a
re straight up and flush
with the base (diagram at
right).
4. Carefully insert new bulb into socket
and push down Bulb Lock until it
snaps into place (Figure 2).
Fig. 1
F
ig. 2
Fuse Replacement Instructions
4
1. Unplug light string from power source.
2. Fuses are located in light string plug.
Slide the fuse access cover away
from cord side (in direction of arrow,
Figure 3) exposing fuses.
3. Remove fuses from compartment
and examine. Replace burnt out fuse
with new one.
4. Close fuse compartment by sliding
access cover back in towards cord
side of plug (Figure 4).
Fig. 3
Fig. 4
Dual Color
®
Lights Function (if equipped)
1. If your tree is equipped with Dual Color LED lights, the black
button on the top of the Music Match unit is used to control the
light functions.
2. By default, the Music Match system allows for only three music-
synced functions: steady warm white, steady multicolor and steady
alternating warm white to multicolor.
3. Connect your Bluetooth device to the Music Match unit as
described under OPERATING INSTRUCTIONS.
4. Press the black button one time each to cycle through and choose
one of the nine functions.
Removing the Music Match device for normal light operation:
disconnect the device cord from the tree light string cord then
disconnect the transformer. Connect one end of the included foot
switch cord to the tree light string cord, then connect the transformer
to the other end of the foot switch cord.
Fig. 1
Fig. 2
Fig. 3
Storage
Remove all holiday decorations. Gently press tips back into center branch. Raise all branches
to original upright position taking care not to place undue pressure on the attached ends of the
branches. When disassembling tree, a twisting motion will help to separate the sections from
each other. All tree parts can be replaced in carton and should be stored in a cool, dry place.