CONTENTS Contents: Safety information Unpacking your appliance Warranty registration Installing your appliance Cabinet clearances Leveling the appliance . Electrical connection installing the anti-IP device Product dimensions MO24BN Product dimensions MOBS and MO24BT Product dimensions MO24BSSM and MO24BTSM . Using your Electronic control Starting your appliance . Turning your appliance "ON" or Adjusting the temperature Beer dispenser operation . Alas .. 1 Door ajar A Temperature sensor fault M Alarm mute .
UNPACKING YOUR APPLIANCE WARNING % A EXCESSIVE WEIGHT HAZARD Use two or more people to move product. Remove interior Packaging Your appliance has been packed for shipment with all parts that could be damaged by movement securely fastened. Remove internal packing materials and any tape holding internal components in place. The owners manual is shipped insides the product in a plastic bag along with the warranty registration card, and other accessory items.
INSTALLING YOUR APPLIANCE Select Location Tha proper location will ensurers peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from jest sources. To ensure your product performs fo specifications, the recommended installation location temperature range is from 55 to 115°F (13 to 46°C). Cabinet Clearance Ventilation is required from the bosom front of the appliance. Esp this area ops and clear of any obstructions.
INSTALLING YOUR APPLIANCE ya Do not remove A Warning ground prong Electrical Shock Hazard » Do not use an extension cord with this appliance. They can be hazardous and can degrade product performance. = This appliance should not, under any circumstance, be installed to an UN-grounded electrical supply. = Do not remove the grounding prong from the power cord. {See Figure 3}. Do not use an adapter. (See Figure 4}. = Do not splash or spray water from a hiss on the Q— appliance.
INSTALLING THE ANT! TIP DEVICE FOR FREESTANDING INSTALLATIONS A WARNING « ALL APPLIANCES CAN TIP RESULTING IN INJURY. » INSTALL THE ANTI-TIP BRACKET PACKED WITH THE APPLIANCE. » FOLLOW THE INSTRUCTIONS BELOW A WARNING If your refrigerator i3 not located under a counts top (fees standing), you must use an anti-tip device installed as per theses instructions.
INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS NOTE | When the floor mounted anti-tip bracket is used the minimum adjusted height of the cabinet is increased by %" (8 mm).
PRODUCT DIMENSIONS MO24BN 20 “34" Tom) | (864b882am) (807am) | (857w 883em) | (80Zeom) | (8B7om) | (M7 2em) | 887om) MO24BNS 140 Ibs MO248NS TISVIEOHZIEA 838k e D Figure 11 * Depth dimension of rough-in opening may vary depend It necessary to gain clearance insides the rough-in ing on each individual installation. To recess entire door °F" opening & hole can be cut through the adjacent dimensional plus 1" (2.
PRODUCT DIMENSIONS MOBS AND MO24BT MO24B5(S) 298 I W | 23T | 28K 485" 28%° MO24BT(S) | (Stem) | (884bBBIem) (807 cm) | (85710 88.3cm) | (80.20m) | {867 em) | {117.90m) | (887 em) MO24BS(S) MO248T(S) 40 bs {#36kg) TIEVIGOHZIISA Figure 13 Figure 12 Figure 14 If necessary fo gain clearance inside the rough-in * Depth dimension of rough-in opening may vary nonindependent a hole can be cut through the adjacent cabling on each individual installation.
PRODUCT DIMENSIONS MO24BSSM AND MO24BTSM Single dispenses tower shown 219 {54.5 cm} 284 {88.7 modem Figure 1§ Electrical Requirements: A grounded 115 volt, 18 amp dedicated circuit is required. Power outset can be located in the back wall behind unit. Follow all local bulling codes when installing electrical and unit. Product weight = 150 bs. (88.2 kg.
USING YOUR ELECTRONIC CONTROL swore v s Figure 16 close-up of control Starting your beer dispenser Pius the beer dispenser power cord inch a wall outlet. Your beer dispenser will begin cooling after power is applied. If your beer dispenser does not start, check that the beer dispenser is muted on and the set temperature is cold enough. Earning your beer dispenser ON or OFF If the beer dispenser is on, the beer dispenser temperature will be shown on the display.
USING YOUR BEER DISPENSER Shelving The uni is shipped with the (2) shelves taps in place in the upper and the lower shelf positions. Remove them from ths refrigerator and arranges them as follows when siting up your unit. If you are not serving beer on tap, your keg dispenser can be used as a refrigerator by placing both shelves on the mounting brackets as shown in Figure 19.
USING YOUR BEER DISPENSER This beer dispensing unit will support one half name! or one quarter {44} barrel, The double draft tower units can support two sixth {34} bares of beer. See chart below for quantity of beer in sate barmen size. 23%" {59.2 om) 14%5° {37 6 cm) 23%e" (58.2 em) Height Gallons Treble A 5 gallon Corny 1/4 Barrel Table B | Caution | Information that follows on pages 13 through 20 does not apply to models MO24BN, as these modals do not include any tap and tower equipment.
single Dispense Tower Kit USING YOUR BEER DISPENSER Double Dispense Tower Kit Connect Figure 28 + Figure 27 i Figure 23 o 9 Double % Single e Dispense Hose clamps Dispenses Tower use for connections Tower Hose clamps . use for connections Figure Anacin) Keg Couplet (A Figure 24 Keg Couplet Keg Couple Figure 30 -~ New plastic washer . New plastic ¢ \C) washstand‘ Regulator § whit red \ & Pound airing 4 COz Tank Figure 25 4 Figure 31 % Pound CO Tank Regulator Fi 26 regulator figure it serine Figure 32 14
USING YOUR BEER DISPENSER } i typical = Diameter dastard @som | ad, L7 upload — oo L (16.2 omy] =@ tan Figure 33 @ A caution ] The cutout dimensions shown in Figure 33 are based on 8 25%:" (64.3 om) deep counter top. Your counter top may be different then this and requires other front to back dimensionless. Refer to the product dimensions on pages 8 and § when determining the required dimensions. Grate from top of beer dispenser— Counter top / §< sump from J infiltrators pack—' 4.
USING YOUR BEER DISPENSER the faucet hands on the tower. Hooking up the keg couplet to the keg: Verify the couplet is in the "OFF™ position {ses Figure the lugs on the keg with the corresponding openings on the keg couplet and tum clockwise until the couplet stops {about 80"}, Push down and twist the top of the couplet clockwise o allow gas {o rents the keg. faucet handier back toward tower fo close the faucet /chain-Tha chain is fastens and paled " 1o the fop of the interior liner.
USING YOUR BEER DISPENSER Optional CO2 tank external mounting bracket: Tha optional mounting bracket is designed to hold the 54 Cylinder that comes with the beer dispenser. Larger cylinders may be purchased from a third parky and mounted externally. Use the hole port on the rear of the cabinet to run the COz line to the keg. Many options are available for mounting the Constant outside of the beer dispenser fo gain additional cold storage spacey inside.
USING YOUR BEER DISPENSER ©0: Regulator {Single Dispense Tower} Your beer dispenser comas quipped with a § pound COz tank and a single gauge regulator, The gauge reads the pressure being supplied 1o the bear keg. Follow the procedural below to adjust the pressure psi {0810 1 bar) for lager beer psi {0.8 to 0.8 bar) for sis's, To adjust the pressure {Single Gauge): Close the shutoff naive at the bottom of the regulator. Be sure the faucet handle is closed on the tower (see Figure 38}.
USING YOUR BEER DISPENSER AND CARE AND CLEANING Drain kit (Al Modish: The drain kit is shipped in Push faucet handier back toward Removable place and ready to use. To empty: Pull drain hose out of tower to close the faucet—~ | grate for cleanliness cap, remove boiler from unit, unscrew cap and dis" ing sump area card waste and rinse bottle. Reinstall bottle in unit.
CARE AND CLEANING Cleaning and Maintaining Dispensing System Ths dispensing system needs (o bs cleaned beefiness usage o prevent spoilage and/or foul taste in your beer. Keg Couplet Cleaning Remove the keg couplet from the keg if necessary. Loss the gas valve(s) below ths regulator, removes both the red gas line{s) and clear beer line{s) from the keg couples) by removing the plastic hiss clamps {See Figure 45). Scan and brush the keg couplet in hot wale or & sanitizing solution.
CARE AND CLEANING Tap Cleaning Kit This is an optional item (pair number 42242373} Kit includes everything fo quickly clean tap. Includes scanning solution, pump, mixing bot lie, brush and wrench. Cleaning the beer line (using tap cleaning kit 42242373): With the faucet removed from the tower (sse page 20) and the keg couplet removed from the keg (see page 20), place the end of the beer line in a pall or pan. Recurs the pump to the tower with the couplet nut provided on the pump assembly.
CARE AND CLEANING Long term storage / internalization: 1. Time to Winterize, when the daily low ambient temperature is at or below 38F. A CAUTION Operating of the unit at ambient temperatures below the recommended Internalization temperature will void your warranty. 2. Tum unit off, (88 page 11}. 3. Remove all contents. 4. If necessary, move the unit so you can gain access {o the rear of the product. 5. Unplug ths unit from the power cubist. 8.
CARE AND CLEANING Leave door open and allow t completely dry out before closing door. Thoroughly clan the door gasket with anti-bacterial cleaner tv be followed with clean tinge water ko remove any residual chemicals. Thoroughly clean the exterior with a cleaner approved for stainless steal . Do not use any abrasive cleaners oF scouring pads. Any mounting hardware / Assigners that are showing signs of corrosion should be replaced.
STAINLESS STEEL MAINTENANCE Background stored in close proximity fo chlorine chemicals. Stainless tiles! does not slain, corrode, or rust as easily ordinary steal, but it Is not stain or corrosion proof. StalnWhizhavar cleaning product you chose, it should be used lass steals can discolor or corrodes if not maintained pro pin strict accordance with the instructions of the cleaner early. manufacturer. Stainless steels differ from ordinary carbon stasis by the amour of chromium present.
DOOR ALIGNMENT AND ENERGY SAVING TIPS Door alignment: The door should be parallel {o the sides and top of the appliance. If alignment is necessary the door may be adjusted by loosening the 2 screws which secures the door adjustment bracket on the bottom of ths door (ses Figure 54a} and adjusting the door SIDS to SIDS. Uss a %" balls wrench for this procedure. (See Figure 54 below). When finished aligning the door, tighten the screws securely. —Door should be parallel to top P ; P appliance.
TROUBLESHOOTING AND OBTAINING SERVICE Before You Call for Service If the appliance appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and rear io the cause and its remedy before calling for service. The problem may be something very simple that can be soiled without a services call.
HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty AGA MARVEL maharanis that it will supply all necessary parts and labor to repair or replace in the end user's home or offices, any component which proves o be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user.