Instructions / Assembly

12”
ONE-PIECE DUAL FLUSH TOILET
6 INSTALLING THE COVER OF
THE FLOOR BOLT
7.INSTALL TANK BUTTON
Nut
1.Remove nut from
push button assembly
Half flush push button
Full flush push button
left right
2. Place push button assembly
through cistern cover. Fit nut
and tighten (Do not over tighten)
3. Ensure full flush button is on the
right hand side so that is lines up
with ‘B’ as shown in the diagram.
Enlarge
Rod
Full flush push button
Half flush push button
A
B
The rods for full and half flush can be adjusted up and down by
turning the rods clockwise (UP) and anti-clockwise (DOWN)
01
Bolt
8. INSTALL TOILET SEAT
Picture 1
Small washer
Big washer
Rubber cork
1. Fit the big washer, small washer, rubber cork
with the bolt sequence.
Picture 2
Inner hinge
Toilet bowl
2
1
3
4
2. Align the inner hinge with toilet bowl’s hole
and insert screws to make the inner hinge fixed.
Picture 3
Toilet seat cover
Outer hinge
5
3. Get the seat cover and outer hinge ready, then,
assembled the outer and inner hinge in place.
Picture 4
Selftapping
screw
6
4. Lift the seat cover up, put the selftapping screws
into composite hole and tighten them up.
CAUTION: DO NOT OVERTIGHTEN THE LOCK-BOLT, AS IT MAY DAMAGE THE SEAT.
WARNING: DO NOT USE PLUMBER’S PUTTY, PIPE DOPE OR ANY OTHER SEALANT ON THE WATER SUPPLY CONNECTION TO THIS TANK.
IF THE CONNECTION LEAKS AFTER HAND TIGHTENING, REPLACE THE SUPPLY LINE. IF THE CONNECTION CONTINUES TO LEAK WITH
THE NEW SUPPLY LINE, REPLACE THE FILL VALVE.
WARRANTY IS VOID IF ANY TYPE OF SEALANT IS USED ON THE WATER SUPPLY CONNECTION.
Part (SS1) and (SS2) are already installed into the
opening when you get the toilet. Click the cover of
the flfloor bolt (SS3) into part (Ss2). Then repeat
the second cover for the other side of the toilet.
To ensure this product is installed properly, please read these instructions carefully before you begin.
(Certain installations may require professional help.) Also be sure your installation conforms to local codes.
CAUTION: HANDLE WITH CARE. VITREOUS CHINAWARE FRAGILE WITH SHARP EDGES IF BROKEN.
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Flathead Screwdriver Adjustable Wrench Sealant Tape Measure
Hacksaw Flexible Supply Hose Water Supply Kit Carpenters Level
1 REMOVE OLD TOILET
a. Turn off water supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove old water supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor flange to block sewer gases from escaping.
d. Remove closet bolts from flange and clean away old wax, putty, etc from base area.
NOTE: MOUNTING SURFACE MUST BE CLEAN AND LEVEL BEFORE NEW TOILET IS INSTALLED.
2 ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange center line must be as listed on chart:
3.INSTALL CLOSET BOLTS
Insert floor bolts into flange channel
with bolt head down (use plastic
retaining washers to hold the bolts in
full-length. Floor bolts should be
parallel to wall and 6” (152mm) apart.
TOILET FLA NGE
FLOO R BOLTS
RETAINI NG WAS HER
4.INSTALL WAX RING
Turn toilet bowl down onto a towel
or cushioned surface. Place the
wax ring around the draining outlet
of the bowl and press firmly enough.
Apply a thin bead of sealant around
toilet base.
SEAL ANT
WAX R ING
5.POSITION TOILET BOWL ON FLANGE
a. Unplug floor waste opening, gently place the bowl in
position with the floor bolts protruding up through the
hole in the base.
b. Press down with slight twisting motion on the top
center of bowl to compress the wax ring creating a
water-tight seal.
c. Place plastic disc, metal washers and nuts o floor
bolts.
FLAN GE
NUT
METAL WASHER
FLOO R BOLT
PLAS TIC DIS C
(“TH IS SIDE U P”)
SUPPLY AS REQ’D
FINIS HED WAL L
FINIS HED F LOOR
12"
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE
ONE-PIECE DUAL FLUSH TOILET
01