INSTALLATION INSTRUCTION for ceiling fan
BBA534002CA Installation & Operating Instructions for the Parrotuncle Owner’s Installation ,Manual Motor is core parts of the fan and the most expensive in all the components. The fan is used currently divided into two major categories of AC motor and DC motor, the AC motor is absolute mainstream. Although the AC motor occupies absolute advantage, but not the best solution. The main problem is common AC motor has big power consumption, high noise, large calorific value.
SAFETY PRECAUTION • WARNING –To make sure power is off before attempting installation. • WARNING – Support Directly From Building Structure. • WARNING –To reduce the risk of fire, electric shock, or injury to persons, unplug or disconnect the appliance from the power supply before the fan installation, cleaning, or servicing. • WARNING –Suitable for use with solid-state speed controls. • WARNING –Do not connect this fan to regulator or dimmer switch.
PARTS & ACCESSORIES Canopy Downrod Housing Blade Transmitter Kit 5 4 1hr 6 3 3hr Transmitter Holder Battery CR Transmitter 1 2 Wall Screw x 2 2032 3V 6hr CR2032/3V Assembly Kit Plastic Anchor x 4 Self Tapping Screw &Washer x 4 2
INSTALLATION INSTRUCTION STEP 1A - CONCRETE CEILING SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX. 1) Use the Mounting Bracket (1) as a guide, mark the spots where the 4 Expansion Bolts (2) will be drilled. 2) Remove the Mounting Bracket (1), drill 4 holes and insert 4 Expansion Bolts (2) into the concrete ceiling, install the mounting bracket and secure with Flat Washers (3), Spring Washers (4) and Nuts (5).
INSTALLATION INSTRUCTION Screw (1) Lock Pin (2) Hanger Ball (3) Canopy (4) Canopy Ring (5) Coupling cover (6) Downrod (7) Clevis pin (8) Bolt (10) Nut (9) Spring Washer (11) Flat Washer (12) Coupling (14) Set Screws (13) 4
INSTALLATION INSTRUCTION STEP 2 1) Remove the Clevis Pin (8), Nut (9), Spring Washers (11), Flat Washers(12) & Bolt (10) on Coupling (14). 2) Loosen the Screw (1) from Hanger Ball (3), remove the Hanger Ball (3) and Lock Pin (2). 3) Route the wires and safety wire from the motor through the Downrod (7). 4) Install the Downrod (7) to Coupling (14) and secure with Bolt (10), Flat Washer (12), Spring Washer (11), Nut (9) & Clevis pin (8).
INSTALLATION INSTRUCTION Safety Wire Clamp STEP 3 1) Raise the fan and place the hanger ball onto mounting bracket. 2) Rotate the fan until the notch on hanger ball snapped into the slot on mounting bracket and sits firmly. NOTE : THE DOWNROD AND HANGER BALL SHOULD NOT ROTATE IF THIS STEP IS DONECORRECTLY. 3) Tighten the safety wire clamp. 4) Place ring of safety wire through the Fan expansion bolt or self tapping screw and fix it to the building structure. 5) Connect the wire connector plugs correctly.
INSTALLATION INSTRUCTION STEP 4 L Led Driver N HT FOR power supply with wire connectors. 2) Insert the controller and led driver into the space of the mounting bracket, and tidy up the wiring. + - LIG FOR LIG HT SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.
TRANSMITTER FUNCTION TRANSMITTER SETTING This DC motor is equipped with self-learning frequency function transmitter. Read all the steps BEFORE proceeding. Each step must be followed exactly in order to program the transmitter. To use factory pre-programmed setting – Skip the below programming steps. Insert battery into transmitter, turn on the power supply to fan and it is ready to use.
TRANSMITTER FUNCTION Forward / Reverse Fan speed (6 speed) Natural wind 5 4 1hr 6 3 3hr 1 2 6hr Power off Timer TRANSMITTER FUNCTION FAN SPEED 5 4 6 3 1 2 Fan speed 1 – 6 control (1-low speed, 6-high speed) Turns off the fan Timing the fan 1hr Auto off after 1 hr 3hr Auto off after 3 hr 6hr Auto off after 6 hr Cancel timing setup Forward or reverse operation: change fan rotating direction. Natural Wind: Press the button to change fan rotating direction.
TRANSMITTER FUNCTION Forward Reverse Fan rotates anti-clockwise creating a downward airflow delivering a cooling effect. Fan rotates clockwise creating an upward airflow moving warm air off the ceiling areas. This function works best at lower fan speed. Suitable for hot weather condition or air-conditioned condition. Suitable for cold weather or air-conditioned condition.
TECHNICAL SPECIFICATIONS 555mm (860mm) ≥ 1000mm ≥ 2300mm 750mm Model No. of blades BBA534002CA 3 Fan width 750mm Light bulb 2 x 25W LED Speed Amps Wattage RPM CFM 1 2 3 4 5 6 0.040 0.051 0.075 0.119 0.190 0.327 1.4 2.4 4.5 8.2 14.1 27.3 88 135 185 235 285 330 600 1000 1350 1750 2150 2600 Voltage 110-120V~ 60Hz Nett weight Gross weight 6.2 kg 7.4 kg Specifications & measurements shown are subject to ±5% variations.
MAINTENANCE Due to the fan’s natural movement, connections may get loose after a period of usage. To ensure a proper and safety usage, inspect the suspension system and tighten all connections every 6 months. Cleaning Cleaning your fan periodically will prolong its useful life. Basic cleaning procedures are as follows: 1. Please shut off the power before you clean the light fan and replace the bulbs. 2. The bulbs and nearby parts will be still hot after the power is shut off.
CAUTION THANK YOU FOR YOUR PURCHASE READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION. IF UNSURE CONSULT A QUALIFIED ELECTRICIAN Thank you for purchasing this quality product. To ensure correct function and safety, please read and save all instructions before using the product LIGHT FAN THE BEST PARTNER OF AIR CONDITIONER & AIR PURIFIER A lot of people think the fan is only used in the summer, actually fan has a great purpose is to speed up the indoor air circulation.
