MULTIPOINT™ Workstation MWS 8840 USER MANUAL
MULTIPOINT™ Workstation MWS 8840 TABLE OF CONTENTS INTRODUCTION .................................................................................. 2 FEATURES ..................................................................................... 2 APPLICATION ................................................................................ 3 PACKAGE CONTENTS .................................................................... 3 MINIMUM SYSTEM REQUIREMENTS ...........................................
MULTIPOINT™ Workstation MWS 8840 INTRODUCTION Thank you for purchasing the MultiPoint Workstation 8840. The MultiPoint Workstation (MWS8840) is designed specifically for Windows MultiPoint Server 2011. Simply connect it to an available USB port on the server and attach a monitor, keyboard, and mouse to add a new workstation. The MWS8840 features four high-speed USB 2.0 ports, audio and microphone ports and a VGA port that supports resolutions up to 1600 x 1200. Add up to ten MWS8840 per server.
MULTIPOINT™ Workstation APPLICATION PACKAGE CONTENTS z z z z z z MWS8840 VESA Mounting kits USB cable (2 Meters) 3A/5V AC Power Adapter Driver CD User Manual 3 MWS 8840
MULTIPOINT™ Workstation MWS 8840 MINIMUM SYSTEM REQUIREMENTS z Available USB 2.0 Port z CPU – One of the following: • x64-based Intel Pentium, Intel quad core (i7, i5, i3), XEON, Intel dual core. • Compatible processor (MultiPoint Server supports up to four core & eight core CPUs on one server) Note: 1) AMD Opteron / Athlon, AMD Embed chipset is not recommend due to unstable keyboard/mouse operation which may not recognize under USB1.1 device. 2) Intel Itanium Processor is not supported.
MULTIPOINT™ Workstation MWS 8840 FOR OPTIMUM VIDEO DISPLAY Technically, short video playbacks can be supported but the operating system needs to be - i7 processor - Intel Sandy bridge chipset Note: Extended video display at full screen is not recommended; it often exhausts CPU and force system with much lower performance. REGULATORY COMPLIANCE FCC / CE / C-tick / VCCI Tested to comply with FCC Standards.
MULTIPOINT™ Workstation MWS 8840 DEVICE INSTALLATION - SOFTWARE Installing the device driver enables Windows MutliPoint Server 2011 to recognize the MWS8840. Please make sure the MWS8840 is unplugged from your server before executing the setup program. Step 1 Insert the Driver installation CD into the CD-ROM drive. The installer should start automatically. If it does not, double click Setup.exe to start the Installation Wizard.
MULTIPOINT™ Workstation MWS 8840 Step 3 License Agreement; review it and check I accept the terms of the license agreement Click Next to accept the License Agreement. Step 4 Setup is searching for installed features... *You may notice the screen flashes during hardware installation. It is part of the normal process. .
MULTIPOINT™ Workstation MWS 8840 Step 5 Driver Installation Wizard, click Finish to continue and restart the computer. INSTALLING MWS8840 HARDWARE Step 1 Connecting monitor to the VGA connector of the MWS8840, turn on the monitor. Connecting power adapter, USB cable, keyboard, and mouse to the MWS8840. Step 2 Connect one end of the USB cable to the MWS8840 and the other end to an available USB 2.0 port of your computer. The driver installation will proceed automatically.
MULTIPOINT™ Workstation MWS 8840 VERIFYING THE MWS8840 CONNECTION Step 1 Right click ‘Manage’ from the ‘computer’ as the screen Step 2 Point to ‘Device Manager’ on the left panel under ‘Server Manager’ go to ‘View’ and click ‘Devices by type’ as the picture showed.
MULTIPOINT™ Workstation MWS 8840 SPLIT SCREEN ON Windows Multipoint Server 2011 Any MultiPoint Server station monitor that has a resolution greater than 1024x768 can be split into two station screens using the split screen task on the Stations tab in MultiPoint Manager. The screen that is present on the monitor at the time that the splitting occurs moves to the left half of the monitor, and a new station’s screen is created on the right half of the same monitor.
MULTIPOINT™ Workstation MWS 8840 Please follow up the steps for split screen as below: Step 1 Please follow up the procedure on illustration for getting into “MultiPoint Manager” as 1. Start -> 2. All Programs -> 3. Windows Multipoint Server --> MultiP oint Ma na ge r Step 2 Select “Stations” on MultiPoint Manager then highlight and click the local station after that click “Split station” under “Selected Item Tasks” as illustration.
MULTIPOINT™ Workstation MWS 8840 Step 3 Click OK to continue NOTE: TO DISABLE SPLIT SCREEN Same procedure as above step1 for getting onto “MultiPoint Manager” and select “Stations” then highlight the local station and click “Unsplit station” under “Selected Item Tasks” as illustration. Then click “OK” on the “Unsplit station” dialog to bring back into single station on the monitor.
MULTIPOINT™ Workstation MWS 8840 ADJUSTING THE SCREEN RESOLUTION By default, Windows MultiPoint Server 2011 will select the recommended resolution for each connected display. However, if you would like to choose a different resolution, follow these steps: Step 1 Please follow up the procedure on illustration for getting into “MultiPoint Manager” as 1. Start -> 2. All Programs -> 3.
MULTIPOINT™ Workstation MWS 8840 Step 3: Click OK to continue Step 4 Press “Ctrl + Alt + Delete” to log in administrator into Maintenance Mode Step 5 Right click on the desktop and choose Screen Resolution from the contextual menu.
MULTIPOINT™ Workstation MWS 8840 Step 6 Click Identify to identify each display. Then click on the display to be adjusted and choose the desired resolution from the Resolution dropdown menu. (suggest: better using the system recommend resolution) DEVICE DRIVER UN-INSTALLATION The following procedure allows you to uninstall the MWS8840 device driver. Please make sure all MWS8840 are unplugged from your server before executing the device driver uninstallation program. Step 1 1. Click Start -> 2.
MULTIPOINT™ Workstation MWS 8840 Step 2 Double click “Uninstall a program” as illustrated on the screen. Step 3 Select the “Magic Control Technology – MWS xx.xx.xxxx.xxxx” item. Click Uninstall button.
MULTIPOINT™ Workstation VESA MOUNTING 18 MWS 8840
MULTIPOINT™ Workstation MWS 8840 TROUBLESHOOTING TIPS The following troubleshooting tips may help if you are experiencing any difficulties using our device. • Check to make sure that all connectors are plugged in correctly. • Make sure that the USB port that you are using is USB 2.0. • Try a different USB 2.0 port • Check to see that the monitor is connected correctly and the power is ON. • Make sure to restart the server after the driver installation.
